Aerospace · Die Casting

Aerospace Die Casting for Lightweight Housings and Brackets

Tuowei Precision is a die casting supplier for housings, covers, brackets and enclosures needed in repeat volumes. We build the tool, cast the parts in non-ferrous alloys, then machine critical bores and faces so each die-cast part arrives ready to assemble, with casting and machining handled by one team.

All uploads are secure and confidential
AS9100D
ISO 9001:2015
In-house CNC finishing
DFM review on every quote
Open steel die casting die with an aluminum casting shot, gates and overflows
Why Die Casting

The Role of Die Casting in Aerospace Manufacturing

Die casting forces molten metal into a hardened steel die, so every shot repeats the same geometry. For parts needed in hundreds or thousands, that repeatability lowers cost well below machining from solid. Thin walls, ribs, bosses and mounting features come out of the die in one piece, which cuts assembly steps and weight. This ability to produce complex shapes at volume makes high-pressure die casting a cornerstone for cabin hardware and electronics boxes, and die casting enables thinner, lighter designs than sheet metal assemblies.

The trade-off is porosity. Trapped gas and shrinkage during solidification can leave small voids inside a casting, so die casting suits housings, covers and brackets far better than pressure-tight or fatigue-critical structure. We review where your part carries load, place gates and overflows to push voids away from critical areas, and tell you when machining from plate is the better choice.

  • Repeatable shapes at volume with low cost per part
  • Thin walls and fine detail with minimal rework
  • Weight savings from light aluminum alloys
  • Casting, machining and finishing in one supply chain
Alloys

Which Materials Are Used for Aerospace Applications

AlloyTypical useNotes
Aluminum A380 / ADC12Avionics housings, covers, bracketsGood strength-to-weight and fluidity; most common choice
Magnesium alloysWeight-critical enclosures and casesLightest structural metal; needs a protective finish
Zinc Zamak 3 / Zamak 5Small detailed parts, connectors, knobsExcellent detail and surface; heavier than aluminum

Aluminum is the default for aerospace casting parts because it balances weight, tensile strength and cost. Magnesium saves more weight but needs coating against heat and corrosion. Zamak suits small, detailed parts where weight matters less. If you are unsure, send your load and environment requirements and we will shortlist the alloy.

CNC machining bearing bores in an aluminum die-cast housing
Process

Our Die Casting Processes

DFM and tool designOur engineers check draft angles, wall thickness and gate positions, then design the die with cavities, cooling channels and ejection.
ToolingThe steel die is CNC machined and EDM finished, then trial shots confirm fill and each tolerance.
CastingCold chamber machines cast aluminum, while hot chamber machines run lower-melting alloys for faster cycles.
Trim, machine and finishGates are trimmed, critical features are machined, and parts are finished and inspected before shipping.
Machining and Finishing

Machined Features for Tight Tolerances

As-cast dimensions are repeatable, but bearing bores, sealing faces and threaded holes usually need CNC machining to reach the tolerances flight hardware demands. We design each housing with machining stock on those features and fixture it on cast datums, so machined features line up with the rest of the part. Anodizing, chromate conversion coating, powder coating and plating protect the surface after machining.

Casting Methods Compared

Pressure Die Casting vs Investment Casting in Aerospace

Engineers comparing casting methods usually weigh three routes:

MethodBest forTrade-off
Die castingHousings, covers, brackets in volumeTooling cost; internal voids limit critical use
Lost-wax castingTurbine blades, superalloy and complex partsSlower and costlier per part
Machining from solidPrototypes and fatigue-critical partsHigher cost per part at volume

Lost-wax foundries handle nickel superalloys and steels for engine parts, which die casting cannot. We do not offer that process and will point you to a specialist foundry. Where volumes are low or the part is critical, our aerospace machined parts service is often the better route.

Vacuum Casting

Aerospace Vacuum Casting for Low-Volume Plastic Parts

When you need 20 to 200 plastic parts before committing to a mold, vacuum casting pours polyurethane resin into a silicone mold under vacuum to remove air bubbles. Parts mimic ABS, PP or elastomers, hold about ±0.15 mm, and simple parts can ship in under 5 days. It is a common bridge for interior trim, covers and test housings. See our vacuum casting service for materials.

Quality

Industry Standards and Quality Control

Our quality system follows standards like AS9100 and ISO 9001 and covers the route from alloy to finished part. We provide material certificates, first article inspection, dimensional reports on machined features and lot traceability on request. Sectioning or X-ray checks by an approved lab can be arranged when your drawing calls for proof of structural integrity. These quality standards are how we deliver precision and reliability on critical applications.

Related Services

Related Manufacturing Solutions From One Supplier

Get a Quote

Request a Die Casting Quote

Send your 3D model, alloy, annual volume and finish requirements. Aerospace manufacturers get tooling and part pricing, realistic lead times and DFM notes on draft, wall thickness and machining stock.

Get Instant Quote
🔒 All uploads are secure and confidential
Get In Touch With Us!
Prompt response guaranteed within 24 hours
🔐 All uploads are secure and confidential
— FAQ —

Frequently Asked Questions

Aerospace
What is die casting used for in aerospace?

It is used for housings, covers, brackets, enclosures and connector bodies needed in repeat volumes. It suits parts with thin walls and complex shapes that would be costly to machine. Fatigue-critical or pressure-tight structure is usually machined or investment cast instead because of the risk of internal voids.

Which alloys are used for cast aerospace components?

Aluminum alloys such as A380 and ADC12 are the most common because they balance weight, strength and cost. Lighter alloys save more weight but need a protective coating. Zinc alloys such as Zamak 3 and 5 suit small, detailed parts where weight matters less.

How do you control voids in cast parts?

We control internal voids through part design, gate and overflow placement, and process settings, and we keep critical machined features away from areas prone to them. When your drawing requires it, sectioning or X-ray inspection can be arranged before parts ship.

Can die-cast parts meet aerospace tolerances?

As-cast features are repeatable, but critical bores, sealing faces and threads usually need machining to reach flight tolerances. We design the casting with machining stock on those features and machine them in-house, so the part arrives ready to assemble.

What is aerospace vacuum casting?

In our service, vacuum casting means pouring polyurethane resin into a silicone mold under vacuum to make 20 to 200 plastic parts. It suits prototypes and short runs of covers, trim and housings. It is different from vacuum investment casting of superalloys, which we do not offer.