Aerospace · Aluminum Extrusion

Aerospace Aluminum Extrusions and Machined Extruded Parts

Tuowei Precision supplies custom aerospace aluminum extrusions and turns extruded shapes into finished parts. We produce 6061 and 6063 sections on press lines from 600 to 3,800 tons, then cut, machine and anodize them, so you receive rails, frames and brackets ready for assembly rather than stock lengths.

All uploads are secure and confidential
AS9100D
ISO 9001:2015
In-house CNC finishing
DFM review on every quote
Cross-sections of aluminum extrusion profiles
Custom vs Stock

Aluminum Extrusions for Aerospace Applications: Custom vs Stock

Most aircraft structures, such as stringers, stiffener sections and wing spars, use 2xxx and 7xxx series alloys bought as mill-certified extruded shapes. Distributors hold a large inventory of aircraft extrusions under Boeing BAC and AND shape numbers, and MRO shops rely on them. If your drawing calls for one of those common shapes, buy it from an approved supplier with full certification.

Where we help is the next step: custom profiles for interiors, ground equipment, UAVs and test rigs, and machining extruded aluminum into finished parts. A custom section can replace a machined part that would otherwise waste most of a solid bar, which cuts cost and lead time on repeat orders.

  • Precision extrusions for rails, channels, frames and heat sinks
  • Accurate cut-to-length with tight length tolerances
  • Machining of holes, slots, pockets and end features
  • Anodizing for corrosion resistance and durability
Alloys

Aircraft Aluminum Extrusions: 6xxx, 2xxx and 7xxx Alloys

AlloyMechanical propertiesTypical use
6061-T6Medium-high tensile strength, weldableGround support frames, brackets, UAV structures
6063-T5/T6Medium strength, best surface finishInterior trim, rails, enclosures, heat sinks
2024Good damage tolerance under tensionWing and fuselage structure (stock shapes)
7075Very high strengthHighly stressed fittings (stock shapes)

We produce custom sections in 6061 and 6063 to ASTM B221, an industry standard for extruded bar and shapes. High-strength aluminum grades are hard alloys usually bought as stock; we can machine those to your drawing when you supply certified material.

CNC machining holes and slots in an aluminum extrusion rail
Process

Our Extrusion Process

Shape and die designIn the design phase, engineers review wall thickness, symmetry and tolerances, then design a solid, hollow or semi-hollow die.
Extrude and ageBillets are preheated to about 400–500°C, pushed through the die, then aged to the specified temper.
Cut and machineSections are cut to length and machined for holes, slots, hinge points and fastener features in our aerospace CNC milling and turning cells.
Finish and inspectParts are anodized or coated, inspected against the drawing and packed to protect visible surfaces.

A new die typically takes 2–4 weeks, and production usually runs 2–3 weeks after samples are approved.

Tolerances

Extrusion Tolerances and Capabilities

FeatureTypical tolerance
Wall thickness up to 3 mm±0.10 mm
Thicker walls±0.30 mm
Machined featuresDown to ±0.025 mm
Press capacity70 lines, 600 to 3,800 tons

Extruded sections carry some twist and bow. Mating surfaces and bores that need tight tolerances are machined downstream rather than relied on as-extruded.

Parts

Extruded Aluminum Parts for Aerospace Manufacturers

  • Seat track and cabin rail sections
  • Interior trim, panel edges and lighting channels
  • Ground support equipment frames and guards
  • UAV booms, arms and tubes
  • Avionics rack rails and heat sinks
  • Test rig and fixture frames
  • Machined brackets cut from extruded sections
Quality

Quality and Documentation

Machining and finishing run under our AS9100D quality system, and our extrusion plants are ISO 9001:2015 certified. We supply material certificates, dimensional reports and lot traceability on request. For flight-critical parts, your program and its FAA approval path decide whether a custom section is acceptable or whether certified stock to an AMS specification is required to protect structural integrity.

Related Services

Related Aerospace Solutions

Get a Quote

Get a Quote for Custom Extrusions

Send your section drawing or 3D model, alloy, temper, lengths, annual volume and finish. Our engineers will return die and part pricing with notes on wall thickness and machining.

Get Instant Quote
🔒 All uploads are secure and confidential
Get In Touch With Us!
Prompt response guaranteed within 24 hours
🔐 All uploads are secure and confidential
— FAQ —

Frequently Asked Questions

Aerospace
What aluminum is used for an aerospace aluminum extrusion?

Structural aircraft sections are mostly 2xxx and 7xxx series alloys because of their strength and fatigue resistance. 6061 and 6063 are used for ground equipment, interiors, UAVs and parts where weldability, surface finish and long-term durability matter more than maximum strength.

Do you supply 2024 and 7075 aerospace extrusions?

We produce custom sections in 6061 and 6063. Standard high-strength aerospace shapes are usually bought from mill-certified distributors. When you supply certified material, we can cut, machine and finish it into parts to your drawing.

What tolerances can extruded sections hold?

Typical tolerances are ±0.10 mm for walls up to 3 mm and ±0.30 mm for thicker walls. Features that need tighter control, such as bores and mating faces, are machined after extrusion to tolerances down to ±0.025 mm.

How long does a custom extrusion take?

A new die typically takes 2–4 weeks, and production usually runs 2–3 weeks after samples are approved. Machining and anodizing add time depending on the part. Your quote confirms the lead time after we review the section and quantity.

Can you machine extruded sections into finished parts?

Yes. We cut sections to length and machine holes, slots, pockets and end features, then anodize or coat the parts. Machining from an extrusion often costs less than machining from solid bar because less material is removed.