Aerospace · Die Casting

Aerospace Die Casting for Lightweight Housings and Brackets

Tuowei Precisionは、 ダイカスト supplier for housings, covers, brackets and enclosures needed in repeat volumes. We build the tool, cast the parts in non-ferrous alloys, then machine critical bores and faces so each die-cast part arrives ready to assemble, with casting and machining handled by one team.

すべてのアップロードは安全かつ機密です。
AS9100D
ISO 9001:2015
社内での CNC 仕上げ加工
すべての見積もりに対するDFMレビュー
アルミニウム鋳造品、ゲート、オーバーフローを備えた、開いた状態の鋼製ダイカスト金型
なぜダイカストなのか

The Role of Die Casting in Aerospace Manufacturing

Die casting forces molten metal into a hardened steel die, so every shot repeats the same geometry. For parts needed in hundreds or thousands, that repeatability lowers cost well below machining from solid. Thin walls, ribs, bosses and mounting features come out of the die in one piece, which cuts assembly steps and weight. This ability to produce complex shapes at volume makes high-pressure die casting a cornerstone for cabin hardware and electronics boxes, and die casting enables thinner, lighter designs than sheet metal assemblies.

The trade-off is porosity. Trapped gas and shrinkage during solidification can leave small voids inside a casting, so die casting suits housings, covers and brackets far better than pressure-tight or fatigue-critical structure. We review where your part carries load, place gates and overflows to push voids away from critical areas, and tell you when machining from plate is the better choice.

  • Repeatable shapes at volume with low cost per part
  • Thin walls and fine detail with minimal rework
  • Weight savings from light aluminum alloys
  • Casting, machining and finishing in one supply chain
合金

Which Materials Are Used for Aerospace Applications

合金代表的な用途備考
アルミニウム A380 / ADC12Avionics housings, covers, bracketsGood strength-to-weight and fluidity; most common choice
マグネシウム合金Weight-critical enclosures and casesLightest structural metal; needs a protective finish
亜鉛・ザマック3/ザマック5Small detailed parts, connectors, knobsExcellent detail and surface; heavier than aluminum

アルミニウム is the default for aerospace casting parts because it balances weight, tensile strength and cost. Magnesium saves more weight but needs coating against heat and corrosion. Zamak suits small, detailed parts where weight matters less. If you are unsure, send your load and environment requirements and we will shortlist the alloy.

CNC machining bearing bores in an aluminum die-cast housing
プロセス

Our Die Casting Processes

DFM and tool designOur engineers check draft angles, wall thickness and gate positions, then design the die with cavities, cooling channels and ejection.
金型The steel die is CNC machined and EDM finished, then trial shots confirm fill and each tolerance.
キャスティングCold chamber machines cast aluminum, while hot chamber machines run lower-melting alloys for faster cycles.
トリミング、機械加工、仕上げGates are trimmed, critical features are machined, and parts are finished and inspected before shipping.
Machining and Finishing

Machined Features for Tight Tolerances

As-cast dimensions are repeatable, but bearing bores, sealing faces and threaded holes usually need CNC加工 to reach the tolerances flight hardware demands. We design each housing with machining stock on those features and fixture it on cast datums, so machined features line up with the rest of the part. Anodizing, chromate conversion coating, powder coating and plating protect the surface after machining.

Casting Methods Compared

Pressure Die Casting vs Investment Casting in Aerospace

Engineers comparing casting methods usually weigh three routes:

方法こんな方に最適トレードオフ
ダイカストHousings, covers, brackets in volume金型費用;内部の空洞により、重要な用途への使用が制限される
Lost-wax castingTurbine blades, superalloy and complex partsSlower and costlier per part
塊材からの切削加工Prototypes and fatigue-critical parts大量生産時の部品単価が高くなる

Lost-wax foundries handle nickel superalloys and steels for engine parts, which die casting cannot. We do not offer that process and will point you to a specialist foundry. Where volumes are low or the part is critical, our aerospace machined parts service is often the better route.

真空鋳造

Aerospace Vacuum Casting for Low-Volume Plastic Parts

When you need 20 to 200 plastic parts before committing to a mold, vacuum casting pours polyurethane resin into a silicone mold under vacuum to remove air bubbles. Parts mimic ABS, PP or elastomers, hold about ±0.15 mm, and simple parts can ship in under 5 days. It is a common bridge for interior trim, covers and test housings. See our vacuum casting service for materials.

品質

Industry Standards and Quality Control

Our quality system follows standards like AS9100 and ISO 9001 and covers the route from alloy to finished part. We provide material certificates, first article inspection, dimensional reports on machined features and lot traceability on request. Sectioning or X-ray checks by an approved lab can be arranged when your drawing calls for proof of structural integrity. These quality standards are how we deliver precision and reliability on critical applications.

関連サービス

Related Manufacturing Solutions From One Supplier

お見積りをご依頼ください

ダイカストの見積もり依頼

Send your 3D model, alloy, annual volume and finish requirements. Aerospace manufacturers get tooling and part pricing, realistic lead times and DFM notes on draft, wall thickness and machining stock.

お見積もり
🔒 すべてのアップロードは安全かつ機密が守られています
お問い合わせ
24時間以内の迅速な対応をお約束します
🔐 すべてのアップロードは安全かつ機密です。
— よくある質問 —

よくある質問

航空宇宙
航空宇宙分野において、ダイカストはどのような用途に使われているのでしょうか?

これは、大量生産が必要なハウジング、カバー、ブラケット、筐体、コネクタ本体などに使用されます。機械加工ではコストがかかりすぎるような、肉厚が薄く形状が複雑な部品に適しています。一方、疲労強度が重要となる構造や気密性が求められる構造については、内部に空洞が生じるリスクがあるため、通常は機械加工やインベストメント鋳造が採用されます。

航空宇宙用鋳造部品には、どのような合金が使用されていますか?

A380やADC12などのアルミニウム合金は、重量、強度、コストのバランスが取れているため、最も一般的に使用されています。より軽量な合金はさらなる軽量化が可能ですが、保護コーティングが必要です。Zamak 3や5などの亜鉛合金は、重量がそれほど重要ではない、小型で細部の精巧さが求められる部品に適しています。

鋳造部品における空洞はどのように制御しますか?

当社は、部品設計、ゲートおよびオーバーフローの位置決め、ならびに工程設定を通じて内部空洞を管理するとともに、重要な機械加工部を空洞が発生しやすい領域から遠ざけています。お客様の図面で必要とされる場合は、部品出荷前に断面検査やX線検査を手配することが可能です。

Can die-cast parts meet aerospace tolerances?

As-cast features are repeatable, but critical bores, sealing faces and threads usually need machining to reach flight tolerances. We design the casting with machining stock on those features and machine them in-house, so the part arrives ready to assemble.

What is aerospace vacuum casting?

In our service, vacuum casting means pouring polyurethane resin into a silicone mold under vacuum to make 20 to 200 plastic parts. It suits prototypes and short runs of covers, trim and housings. It is different from vacuum investment casting of superalloys, which we do not offer.