Aerospace · Die Casting

Aerospace Die Casting for Lightweight Housings and Brackets

图威精密是一家 压铸 supplier for housings, covers, brackets and enclosures needed in repeat volumes. We build the tool, cast the parts in non-ferrous alloys, then machine critical bores and faces so each die-cast part arrives ready to assemble, with casting and machining handled by one team.

所有上传内容均安全保密
AS9100D
ISO 9001:2015
内部 CNC精加工
每份报价单均进行DFM审查
一个敞开式钢制压铸模具,内含铝铸件、浇口和溢流口
为什么选择压铸

The Role of Die Casting in Aerospace Manufacturing

Die casting forces molten metal into a hardened steel die, so every shot repeats the same geometry. For parts needed in hundreds or thousands, that repeatability lowers cost well below machining from solid. Thin walls, ribs, bosses and mounting features come out of the die in one piece, which cuts assembly steps and weight. This ability to produce complex shapes at volume makes high-pressure die casting a cornerstone for cabin hardware and electronics boxes, and die casting enables thinner, lighter designs than sheet metal assemblies.

The trade-off is porosity. Trapped gas and shrinkage during solidification can leave small voids inside a casting, so die casting suits housings, covers and brackets far better than pressure-tight or fatigue-critical structure. We review where your part carries load, place gates and overflows to push voids away from critical areas, and tell you when machining from plate is the better choice.

  • Repeatable shapes at volume with low cost per part
  • Thin walls and fine detail with minimal rework
  • Weight savings from light aluminum alloys
  • Casting, machining and finishing in one supply chain
合金

Which Materials Are Used for Aerospace Applications

合金典型用途说明
A380/ADC12 铝合金Avionics housings, covers, bracketsGood strength-to-weight and fluidity; most common choice
镁合金Weight-critical enclosures and casesLightest structural metal; needs a protective finish
锌-锌合金3 / 锌-锌合金5Small detailed parts, connectors, knobsExcellent detail and surface; heavier than aluminum

铝质 is the default for aerospace casting parts because it balances weight, tensile strength and cost. Magnesium saves more weight but needs coating against heat and corrosion. Zamak suits small, detailed parts where weight matters less. If you are unsure, send your load and environment requirements and we will shortlist the alloy.

CNC machining bearing bores in an aluminum die-cast housing
过程

Our Die Casting Processes

DFM and tool designOur engineers check draft angles, wall thickness and gate positions, then design the die with cavities, cooling channels and ejection.
工具The steel die is CNC machined and EDM finished, then trial shots confirm fill and each tolerance.
选角Cold chamber machines cast aluminum, while hot chamber machines run lower-melting alloys for faster cycles.
修边、机加工和精加工Gates are trimmed, critical features are machined, and parts are finished and inspected before shipping.
Machining and Finishing

Machined Features for Tight Tolerances

As-cast dimensions are repeatable, but bearing bores, sealing faces and threaded holes usually need 数控加工 to reach the tolerances flight hardware demands. We design each housing with machining stock on those features and fixture it on cast datums, so machined features line up with the rest of the part. Anodizing, chromate conversion coating, powder coating and plating protect the surface after machining.

Casting Methods Compared

Pressure Die Casting vs Investment Casting in Aerospace

Engineers comparing casting methods usually weigh three routes:

方法最适合权衡
压铸Housings, covers, brackets in volume模具成本;内部气孔限制了关键用途
Lost-wax castingTurbine blades, superalloy and complex partsSlower and costlier per part
从实件加工Prototypes and fatigue-critical parts批量生产时单件成本较高

Lost-wax foundries handle nickel superalloys and steels for engine parts, which die casting cannot. We do not offer that process and will point you to a specialist foundry. Where volumes are low or the part is critical, our aerospace machined parts service is often the better route.

真空铸造

Aerospace Vacuum Casting for Low-Volume Plastic Parts

When you need 20 to 200 plastic parts before committing to a mold, vacuum casting pours polyurethane resin into a silicone mold under vacuum to remove air bubbles. Parts mimic ABS, PP or elastomers, hold about ±0.15 mm, and simple parts can ship in under 5 days. It is a common bridge for interior trim, covers and test housings. See our vacuum casting service for materials.

质量

Industry Standards and Quality Control

Our quality system follows standards like AS9100 and ISO 9001 and covers the route from alloy to finished part. We provide material certificates, first article inspection, dimensional reports on machined features and lot traceability on request. Sectioning or X-ray checks by an approved lab can be arranged when your drawing calls for proof of structural integrity. These quality standards are how we deliver precision and reliability on critical applications.

相关服务

Related Manufacturing Solutions From One Supplier

获取报价

索取压铸报价

Send your 3D model, alloy, annual volume and finish requirements. Aerospace manufacturers get tooling and part pricing, realistic lead times and DFM notes on draft, wall thickness and machining stock.

获取即时报价
🔒 所有上传内容均安全且保密
与我们联系!
保证在24小时内及时回复
🔐 所有上传内容均安全保密
— 常见问题 —

常见问题

航空航天
压铸在航空航天领域有哪些用途?

该工艺适用于需要批量生产的壳体、盖板、支架、外壳和连接器本体。它特别适合壁薄且形状复杂的零件,因为此类零件若采用机加工会成本较高。对于疲劳关键或需保持气密性的结构,通常会采用机加工或失蜡铸造工艺,因为存在内部气孔的风险。

航空航天铸件通常采用哪些合金?

A380和ADC12等铝合金最为常见,因为它们在重量、强度和成本之间取得了平衡。更轻的合金虽然能进一步减轻重量,但需要涂覆保护性涂层。Zamak 3和5等锌合金则适用于对重量要求不高的、结构精细的小型零件。

如何控制铸件中的气孔?

我们通过零件设计、浇口和溢流口的布置以及工艺参数设置来控制内部气孔,并将关键的机加工特征远离易产生气孔的区域。如果您的图纸有要求,可在零件发货前安排进行剖面检查或X射线检测。

Can die-cast parts meet aerospace tolerances?

As-cast features are repeatable, but critical bores, sealing faces and threads usually need machining to reach flight tolerances. We design the casting with machining stock on those features and machine them in-house, so the part arrives ready to assemble.

What is aerospace vacuum casting?

In our service, vacuum casting means pouring polyurethane resin into a silicone mold under vacuum to make 20 to 200 plastic parts. It suits prototypes and short runs of covers, trim and housings. It is different from vacuum investment casting of superalloys, which we do not offer.