IATF 16949 CERTIFIED · SHENZHEN

Automotive Injection Molding for Interior, Exterior and Under-Hood Parts

Tuowei Precision provides automotive injection molding for clips, housings, trim, connectors and EV parts. We design and build each automotive injection mold in-house, run it on presses from 90 to 830 tons, and inspect every lot under an IATF 16949 quality system, so each automotive part stays consistent from the first shot to the last.

All uploads are secure and confidential
Why Injection Molding

Why Plastic Injection Molding in Automotive Manufacturing Pays Off

A modern car carries hundreds of plastic parts, from door clips to air vents and battery covers. Injection molding is used for most of them because, once the mold is built, every cycle on the injection molding machine produces the same molded part at low cost. That is why the injection moulding industry supplies so much of automotive production. Replacing metal brackets and housings with molded plastic components also cuts weight, which helps fuel efficiency and EV range.

The trade-off is the mold. An injection mold is a fixed investment, and changing the mold after steel is cut costs time and money, so every mold decision deserves care. For fewer than a few hundred parts, 3D printing or vacuum casting is usually cheaper. That is why we run a full DFM review and free mold flow analysis before tooling starts.

Plastic injection molding machine producing automotive parts
Low cost per molded part at volume
Complex shapes with clips, ribs and bosses in one piece
Consistent quality across thousands of cycles
Lighter parts than metal equivalents
Process

The Injection Molding Process on Every Injection Molding Machine

01DFM and mold flow analysisOur engineers check wall thickness, draft angles, gates and undercuts, then simulate how the resin fills the mold cavity to predict sink, warpage and weld lines. Most mold problems are cheaper to fix here than in steel.
02Mold design and toolingThe automotive injection mold is CNC machined and EDM finished, with mold components held to ±0.02 mm for high precision. Cooling channels and ejection are designed so the mold runs a stable cycle on our injection machines.
03Molding and process lockTrial shots confirm fill and dimensions. After first article approval, the molding process settings are locked and recorded for every lot, so the mold, the material and the press all stay matched.
04Inspection and deliveryCritical dimensions are measured, parts are packed to protect visible surfaces, and documents ship with the order.
Multi-cavity steel injection mold tool for automotive parts
Tooling

Automotive Injection Mold Tooling and Molding Equipment

Mold choice depends on volume. An aluminum mold suits around 5,000 to 10,000 cycles and is faster to build, which makes it a good bridge for test builds. A hardened steel mold runs 100,000 to over 1,000,000 cycles and is the right choice for production programs. A multi-cavity mold or family mold lowers cost per part further once a design is frozen. Our presses range from 90 to 830 tons, so we match the press to the mold size rather than forcing a small mold onto an oversized machine. Learn more about our injection mold tooling.

Materials

Plastic Materials for Automotive Applications

Material decides heat, chemical and impact performance in each vehicle, and it also changes how the injection mold must be cooled and vented. These are the plastic materials automotive engineers ask about most:

MaterialWhy it is usedTypical parts
PP (polypropylene)Low cost, chemical resistant, lightBumper parts, trim, fluid reservoirs
ABS and PC/ABSTough, good surface finishDashboard parts, bezels, housings
PA66 (nylon, glass-filled)Strength and heat resistanceUnder-hood brackets, clips, fan shrouds
PC (polycarbonate)Clear and impact resistantLight covers, lenses, display windows
POM (acetal)Low friction, wear resistantGears, fasteners, latches
TPE and LSRFlexible and sealingSeals, grommets, soft-touch grips
Injection molded plastic automotive components

Glass-filled thermoplastic grades add stiffness but increase mold wear, and heat near the engine rules out many commodity resins. Recycled content is possible on some non-visible parts if your OEM approves it. Send your material spec with the drawing and we will confirm the grade and the injection mold steel before quoting. Every injection mold is sized for the shrinkage of the chosen resin.

Parts

Injection Molded Parts for the Automotive Sector

01Dashboard trim
02Air vents
03Door handles
04Switch bezels
05Grille inserts
06Mirror housings
07Lighting housings
08Fan shrouds
09Connector bodies
10Sensor housings
11EV battery covers
12Charging port housings

Large painted body panels such as full bumper fascias need very large presses and paint lines. Our range suits the clips, housings, trim and electrical automotive plastic components that make up most of the plastic count in a car or truck, for both OEM programs and the automotive aftermarket.

Techniques

Advanced Injection Molding Techniques for Complex Automotive Parts

Automotive insert molding with metal inserts

Automotive Insert Molding

Insert molding places a metal insert in the mold and encapsulates threaded inserts, pins or contacts in one shot, which removes press-fit steps on the assembly line and improves pull-out strength.

Automotive overmolding soft-touch layer over rigid part

Automotive Overmolding

Overmolding adds a soft-touch or sealing layer over a rigid substrate. It is also called 2K molding when both materials are shot in one mold, and it is common on grips, knobs and sealed connector housings.

Gas-assist injection molding of a hollow automotive part

Gas-Assist and Micro Molding

Gas-assist molding hollows thick sections to prevent sink and save weight, which supports lightweighting in every electric vehicle. Micro injection molding produces small connector and sensor parts, and precision molding of this kind needs a well-vented injection mold and tight temperature control.

Quality

IATF 16949-Certified Injection Molding Quality

CMM inspection of automotive parts for IATF 16949 quality

Every injection mold and every molded part runs through a quality system built on IATF 16949 and ISO 9001. We use scientific molding to lock process parameters, run in-cavity pressure sensors during production, and verify dimensions with a CMM after each lot. PPAP documentation, first-article inspection reports, and full material traceability come standard on automotive programs.

IATF 16949 & ISO 9001 certified facility
Scientific molding with in-cavity pressure monitoring
CMM dimensional verification on every lot
PPAP Level 3 documentation packages
Full material traceability and CoC
Related Services

Complete Automotive Manufacturing Services

Injection molding is one part of our automotive manufacturing capability. We also support these processes under the same IATF 16949 quality system:

01Automotive 3D Printing — Rapid prototypes and bridge-production parts in engineering-grade polymers and metals.
02Sheet Metal Fabrication — Brackets, enclosures and structural panels stamped or laser-cut from steel and aluminum.
03Automotive Prototyping — CNC, SLA and SLS prototypes for form-fit-function testing before tooling.
04Automotive Die Casting — High-pressure aluminum and zinc die-cast housings, brackets and heat sinks.
Supplier Selection

How to Choose an Automotive Injection Molding Supplier

Selecting the right injection molding company for automotive parts is a decision that affects cost, quality and time to market. Look for these capabilities before you commit:

IATF 16949 certification — the baseline quality standard every Tier 1 and Tier 2 supplier must meet.
In-house mold making — suppliers who build their own injection molds control lead time and can iterate faster during mold trials.
Scientific molding capability — data-driven process setup reduces scrap and ensures part-to-part consistency.
Material expertise — experience with automotive-grade nylon, POM, PBT and polycarbonate matters for under-hood and structural parts.
Secondary operations — painting, pad printing, ultrasonic welding and assembly under one roof cut logistics cost.
Transparent quoting — a detailed quote that separates tooling cost from piece price helps you plan budgets accurately.
Get Started

Request Your Automotive Injection Molding Quote

Upload your 3D CAD files and let our engineering team review your automotive injection molding project. We respond within 24 hours with a detailed quote covering tooling, piece price and lead time.

Get Instant Quote
FAQ

Automotive Injection Molding — Frequently Asked Questions

What plastics are used in automotive injection molding?

Common automotive injection molding materials include nylon (PA6, PA66), polypropylene (PP), ABS, polycarbonate (PC), POM (acetal), PBT, and glass-fiber reinforced grades. Material selection depends on temperature, chemical exposure, structural load and surface finish requirements.

What is the typical lead time for an automotive injection mold?

A production injection mold for automotive parts takes 4–8 weeks depending on complexity, number of cavities and steel grade. Prototype molds in aluminum can be ready in 2–3 weeks for design verification.

Do you offer low-volume injection molding for automotive prototypes?

Yes. We run low-volume injection molding from 100 to 10,000 parts using aluminum or soft-steel molds, which lowers upfront tooling cost and supports pilot production before committing to a hardened-steel tool.

What quality certifications does Tuowei hold for automotive work?

Tuowei operates under an IATF 16949 and ISO 9001 certified quality management system. We provide PPAP Level 3 documentation, first-article inspection reports, material certificates and full dimensional reports on every automotive program.

Can you handle insert molding and overmolding for automotive connectors?

Yes. We run both insert molding and overmolding (2K molding) on dedicated presses. These processes are used for automotive connectors, sealed housings and soft-grip components that combine a rigid substrate with a flexible or conductive insert.

Let’s Build What’s Next

Partner With Tuowei Precision for CNC Machined Parts

From rapid prototypes to scalable production, Tuowei Precision delivers precision and consistency at every step, with the highest-quality CNC machined parts we can produce. Send your drawings and our team will reply within 24 hours.

  • Established engineering skills.
  • Global project support
  • Advanced CNC solutions
  • Co-creation of products.
  • Expandable capacity of production.
Get Instant Quote
🔒 All uploads are secure and confidential
Get In Touch With Us!
Prompt response guaranteed within 24 hours
🔐 All uploads are secure and confidential

Customer Reviews

Discover why businesses trust TUOWEI. Our clients value our precision, efficiency, and reliability, delivering seamless manufacturing solutions that consistently exceed expectations. Explore their experiences and success stories with our services.

— Related Industries —

Industry Expertise Beyond the Automotive Industry

With millions of precision components produced, Tuowei Precision serves a wide range of industries. The same tolerance and documentation discipline behind our automotive work also supports aerospace machining, robotics and medical device programs.

Explore Insights & Innovation

Read our latest guides on CNC machining, materials, finishing and industry trends to make better production decisions.