جدول المحتويات

دقة تووي

هل تحتاج إلى حلول متخصصة في مجال التصنيع الآلي؟ فريقنا في Tuowei Precision جاهز لمساعدتك في تلبية جميع احتياجاتك التصنيعية. تواصل معنا اليوم للحصول على عرض أسعار لمشاريعك الجارية أو المرتقبة!

Swiss screw machining services - Swiss-type CNC lathe turning a small brass precision part

Swiss screw machining produces small, long and slender precision parts at high volume with tolerances conventional lathes struggle to hold. Originally developed for Swiss watchmaking, today’s CNC Swiss-type lathes make connector pins, medical components, shafts and fittings by the million. This guide explains how the sliding-headstock design actually works, what tolerances and sizes are realistic, which materials run best, when Swiss turning beats conventional turning — and when it doesn’t.

How a Swiss-Type Lathe Works

The defining feature of a Swiss-type (sliding headstock) lathe is the guide bushing. Bar stock is gripped by a collet in the headstock, which slides along the Z-axis and feeds the bar through a carbide-lined guide bushing. Cutting tools work on the material immediately next to the bushing — typically within 1–3 mm of support.

Because the workpiece is supported at the exact point of cutting, deflection is nearly eliminated. That is why a Swiss machine can turn a Ø2 mm shaft 40 mm long (L/D of 20:1) and still hold a few microns — geometry that would chatter or bend on a conventional lathe, where the tool may work far from the chuck.

Modern CNC Swiss machines add live tooling, sub-spindles and back-working stations, so a part is turned, milled, cross-drilled, threaded and cut off complete — no second operation.

Achievable Tolerances and Part Sizes

Parameter Typical Capability
Bar diameter range Ø0.5 – Ø38 mm (most Swiss machines)
Diameter tolerance ±0.005 mm standard; ±0.002 mm on controlled features
Length tolerance ±0.01 mm typical
Concentricity 0.005 mm (single setup, bushing-supported)
تشطيب السطح Ra 0.4 – 0.8 µm turned; Ra 0.2 µm achievable
Length-to-diameter ratio Up to 20:1 without steady rest
Economic quantities ~500 to 1,000,000+ pieces

Swiss Machining vs Conventional CNC Turning

العامل Swiss-type lathe Conventional CNC lathe
Best part size Ø0.5–38 mm, long/slender Ø10–600 mm, short/stocky
Slender parts (L/D > 3) Excellent — bushing support Needs tailstock/steady rest
Cycle time (small parts) Seconds — done-in-one Longer; often 2 operations
Setup cost Higher — justified by volume Lower — fine for small lots
Ideal quantities حجم كبير 1 – 5,000

For larger or lower-volume turned work, see our CNC turning service و CNC turned parts الصفحة.

Materials for Swiss Screw Machining

Bar stock quality matters: Swiss machines feed ground or drawn bar through the guide bushing, so diameter consistency of the raw material directly affects the bushing fit and final tolerance.

Typical Swiss-Machined Parts

  • Electronic connector pins, sockets and ferrules
  • Medical bone screws, dental implant components, surgical instrument shafts
  • Fuel system and hydraulic fittings
  • Watch components, sensor housings, valve spools
  • Shafts and worms for micro motors

Cost Drivers: What Makes a Swiss Part Cheap or Expensive

  1. الكمية: setup (programming, tool layout, bushing change) spreads across the run — unit prices fall steeply up to ~10,000 pcs.
  2. Material machinability: C360 brass runs 2–3× faster than 316 stainless or titanium.
  3. Tightest tolerance on the drawing: every feature at ±0.002 mm forces slower feeds and 100% gauging — tolerance only what the function needs.
  4. Cross features: live-tool milling and cross-drilling add cycle time; simple turned profiles are fastest.
  5. Bar diameter utilization: parts near standard bar sizes waste less material.

Limitations to Know

  • Diameter cap: above ~Ø38 mm, conventional turning takes over.
  • Low volumes: under a few hundred pieces, setup cost usually favors a conventional CNC lathe.
  • Remnant loss: each bar leaves an unusable remnant; very expensive materials need yield planning.

الأسئلة الشائعة

What is a Swiss screw machine?

A sliding-headstock lathe that feeds bar stock through a guide bushing, supporting the workpiece at the cutting point. It excels at small-diameter, long, high-precision parts in high volumes.

Why is it called Swiss machining?

The design was developed in late-1800s Switzerland to mass-produce watch components — tiny shafts and screws needing watchmaker precision at industrial quantities.

What tolerance can Swiss machining hold?

±0.005 mm is routine on diameters; ±0.002 mm is achievable on controlled features with good bar stock and temperature control.

Swiss machining vs screw machining — any difference?

“Screw machining” historically covers all automatic bar-fed lathes (including cam-driven multi-spindles); Swiss screw machining specifically means the sliding-headstock, guide-bushing type — today usually CNC.

Swiss Screw Machining at Tuowei Precision

Tuowei Precision runs CNC Swiss-type lathes with live tooling and sub-spindles for small precision parts from Ø0.5 to Ø38 mm — connector pins to implant screws — with 100% critical-dimension gauging. Combine Swiss parts with our خدمات التصنيع الآلي باستخدام الحاسب الآلي الرقمي or a full contract machining program. Send your drawing for a quote within 24 hours.

صورة لأحد أعضاء فريق «تووي بريسيشن» يرتدي قميص بولو أزرق أمام آلات CNC غير واضحة المعالم في المصنع
نبذة عن المؤلف
آندي

مهندس تصنيع في شركة tuoweiprecision

بقلم آندي، مهندس تصنيع في شركة TUOWEI Precision. يتخصص آندي في التصنيع باستخدام الحاسب الآلي (CNC) والتصنيع الدقيق وهندسة الإنتاج، ويتمتع بخبرة عملية في دعم المشاريع بدءًا من النماذج الأولية السريعة وصولًا إلى الإنتاج على نطاق واسع. وهو يعمل عن كثب مع فرق الهندسة والتصنيع لتقييم المواد والتفاوتات المسموح بها وعمليات التصنيع وقابلية التصميم للتصنيع. تقدم مقالاته رؤى عملية ومستندة إلى المعرفة التقنية لمساعدة المهندسين والمشترين على اتخاذ قرارات تصنيع أفضل، وتحسين كفاءة الإنتاج، وتحقيق جودة متسقة للأجزاء. اكتشف حلول التصنيع باستخدام الحاسب الآلي (CNC) والتصنيع المخصص التي تقدمها TUOWEI Precision لمشروعك القادم.

لنبني المستقبل معًا

تعاون مع شركة «تووي بريسيجن» لتحويل رؤيتك إلى واقع

بدءًا من النماذج الأولية السريعة وصولاً إلى الإنتاج القابل للتوسع، تقدم شركة Tuowei Precision خدمات تصنيع موثوقة باستخدام الحاسب الآلي (CNC) تتسم بالدقة والاتساق في كل خطوة. ابدأ مشروعك اليوم.

تواصل معنا!
نضمن الرد السريع في غضون 24 ساعة
🔐 جميع التحميلات آمنة وسرية

استكشف الرؤى والابتكار

اقرأ أحدث أدلةنا حول التصنيع باستخدام الحاسب الآلي (CNC) والمواد والتشطيب واتجاهات الصناعة لاتخاذ قرارات إنتاجية أفضل.

تواصل معنا!
نضمن الرد السريع في غضون 24 ساعة
🔐 جميع التحميلات آمنة وسرية