جدول المحتويات

دقة تووي

هل تحتاج إلى حلول متخصصة في مجال التصنيع الآلي؟ فريقنا في Tuowei Precision جاهز لمساعدتك في تلبية جميع احتياجاتك التصنيعية. تواصل معنا اليوم للحصول على عرض أسعار لمشاريعك الجارية أو المرتقبة!

CNC turned parts - precision aluminum stainless steel and brass shafts pins and fittings

CNC turned parts are components produced on computer-controlled lathes — shafts, pins, bushings, fittings, connectors and housings with rotational geometry. As a dedicated turned parts manufacturer, Tuowei Precision produces them from Ø0.5 mm Swiss-machined pins to Ø600 mm flanges, in one-off prototypes or 100,000-piece production runs. This page details the capabilities, achievable tolerances, material options, and the design decisions that make a turned part cheaper and better.

Turned Parts Manufacturing Capabilities

Parameter القدرة
Diameter range Ø0.5 – Ø600 mm
Max turned length 1,200 mm between centers
Machines CNC lathes, turn-mill centers (live tooling, Y-axis, sub-spindle), Swiss-type lathes
Diameter tolerance ±0.01 mm standard; ±0.005 mm precision; ±0.002 mm ground
Concentricity / runout 0.01 mm standard; 0.005 mm same-setup features
تشطيب السطح Ra 1.6 µm standard; Ra 0.4–0.8 µm fine turning; Ra 0.1 µm ground
المواضيع Metric M1–M64, UNC/UNF, NPT/BSP, trapezoidal, custom
Quantities 1 – 100,000+ (Swiss lines for high volume)

Done-in-One: Turn-Mill Parts

Most “turned” parts aren’t purely round: they carry cross-holes, flats, keyways and milled pockets. Our turn-mill centers with live tooling and sub-spindles complete these features in the same setup as the turning — which is what actually protects your tolerances:

  • Position accuracy: cross-features located to the turned datum without re-fixturing error
  • Concentricity: front and back features finished without re-chucking (sub-spindle pickup)
  • Cost: one cycle replaces two machines, two setups and queue time between them

For the process fundamentals, see our guide to what CNC turning is وـ CNC turning service الصفحة.

Material Guide for Turned Parts

المواد قابلية المعالجة الآلية الأفضل لـ
نحاس C360 Excellent (100% index) Fittings, valves, connectors — التصنيع باستخدام الحاسب الآلي (CNC) للنحاس الأصفر
Aluminum 6061/2011 ممتاز Lightweight housings, spacers
Free-cutting steel 12L14 جيد جدًا High-volume shafts and pins
Alloy steel 4140 جيد Loaded shafts, heat-treatable
Stainless 303 جيد Corrosion-resistant hardware
Stainless 316 / 17-4PH معتدل Marine, medical, high-strength
Titanium Gr2/Gr5 Challenging Aerospace, implants — التصنيع باستخدام الحاسب الآلي (CNC) لمادة التيتانيوم
النحاس C110 Moderate (gummy) Electrical contacts — copper CNC machining
POM / PEEK / PTFE ممتاز Insulating bushings — plastic machining

Design Tips That Cut the Cost of Turned Parts

  1. Start from standard bar sizes: a Ø19.5 mm part from Ø20 bar machines fast; Ø21 mm forces the next bar size and wastes material.
  2. Avoid slender ratios: keep unsupported L/D under 3:1 for conventional turning — or expect Swiss machining (great) or steady rests (slower). Above 8:1, specify straightness realistically.
  3. Tolerance only what matters: every ±0.005 mm dimension adds gauging time; leave the rest at ISO 2768-f.
  4. Give thread relief and sharp-corner relief: undercuts at thread ends and shoulders let tools finish cleanly.
  5. Standard internal radii: corner radii ≥0.4 mm match standard insert noses; sharp internal corners need extra operations.
  6. Mind deep small holes: drilled depth beyond 8× diameter raises cost; beyond 12× needs gun drilling.

Quality Control for Turned Components

  • In-process gauging on first-offs and at set intervals (micrometers, air gauges for tight bores)
  • CMM inspection of critical dimensions with reports shipped per lot
  • Thread verification with GO/NO-GO gauges (6g/6H)
  • Runout and concentricity checks on V-blocks or between centers
  • Material mill certificates and full traceability per batch

الأسئلة الشائعة

What are CNC turned parts?

Components machined on CNC lathes where the workpiece rotates against a cutting tool — producing cylindrical geometry such as shafts, bushings, pins, fittings and threaded parts, often finished with milled cross-features on turn-mill machines.

What tolerance can turned parts hold?

±0.01 mm is routine on diameters; ±0.005 mm on precision features in a single setup; ±0.002 mm with cylindrical grinding after turning.

What is the difference between turned parts and milled parts?

Turned parts rotate against a fixed tool (round geometry — shafts, bushings); milled parts stay fixed while the tool rotates (prismatic geometry — plates, housings). Many components combine both on turn-mill centers.

What quantities do you manufacture?

From a single prototype on a CNC lathe to 100,000+ parts per year on Swiss-type machines — same drawing, scaled pricing at your quantity breaks.

Order Custom CNC Turned Parts From Tuowei Precision

Send your STEP file and drawing for a quote within 24 hours — covering material options, quantity breaks and lead time. For small-diameter high-volume work see Swiss screw machining services; for complete programs with milling, finishing and managed inventory, see contract machining services or our full خدمات التصنيع الآلي باستخدام الحاسب الآلي الرقمي.

صورة لأحد أعضاء فريق «تووي بريسيشن» يرتدي قميص بولو أزرق أمام آلات CNC غير واضحة المعالم في المصنع
نبذة عن المؤلف
آندي

مهندس تصنيع في شركة tuoweiprecision

بقلم آندي، مهندس تصنيع في شركة TUOWEI Precision. يتخصص آندي في التصنيع باستخدام الحاسب الآلي (CNC) والتصنيع الدقيق وهندسة الإنتاج، ويتمتع بخبرة عملية في دعم المشاريع بدءًا من النماذج الأولية السريعة وصولًا إلى الإنتاج على نطاق واسع. وهو يعمل عن كثب مع فرق الهندسة والتصنيع لتقييم المواد والتفاوتات المسموح بها وعمليات التصنيع وقابلية التصميم للتصنيع. تقدم مقالاته رؤى عملية ومستندة إلى المعرفة التقنية لمساعدة المهندسين والمشترين على اتخاذ قرارات تصنيع أفضل، وتحسين كفاءة الإنتاج، وتحقيق جودة متسقة للأجزاء. اكتشف حلول التصنيع باستخدام الحاسب الآلي (CNC) والتصنيع المخصص التي تقدمها TUOWEI Precision لمشروعك القادم.

لنبني المستقبل معًا

تعاون مع شركة «تووي بريسيجن» لتحويل رؤيتك إلى واقع

بدءًا من النماذج الأولية السريعة وصولاً إلى الإنتاج القابل للتوسع، تقدم شركة Tuowei Precision خدمات تصنيع موثوقة باستخدام الحاسب الآلي (CNC) تتسم بالدقة والاتساق في كل خطوة. ابدأ مشروعك اليوم.

تواصل معنا!
نضمن الرد السريع في غضون 24 ساعة
🔐 جميع التحميلات آمنة وسرية

استكشف الرؤى والابتكار

اقرأ أحدث أدلةنا حول التصنيع باستخدام الحاسب الآلي (CNC) والمواد والتشطيب واتجاهات الصناعة لاتخاذ قرارات إنتاجية أفضل.

تواصل معنا!
نضمن الرد السريع في غضون 24 ساعة
🔐 جميع التحميلات آمنة وسرية