Aerospace · Injection Molding

Aerospace Plastic Injection Molding for Flight-Ready Components

Tuowei Precision is a precision 注塑 partner for cabin trim, electrical housings, connector bodies, clips and UAV parts. We design and build each injection mold in-house, run it on machines from 90 to 830 tons, and inspect every lot, so your custom plastic components repeat from the first shot to the last.

所有上传内容均安全保密
AS9100D
ISO 9001:2015
内部 CNC精加工
每份报价单均进行DFM审查
Molded aerospace plastic parts in Ultem, PEEK and black engineering plastic
为什么选择注塑成型

Why Aerospace Injection Molding Pays Off

Every gram matters on an aircraft, and replacing machined metal brackets, clips and housings with molded thermoplastic or composite-filled parts is one of the simplest ways to save weight and improve fuel efficiency. Once the tool is built, injection molding produces complex plastic components with ribs, snaps and bosses at low cost per part, which also cuts assembly time.

The catch is that the 注塑模具 is a fixed investment. For fewer than a few hundred parts, 3D printing or vacuum casting is usually cheaper, and design changes after the tool is cut cost time and money. That is why we run a full manufacturability and mold flow review before any steel is machined, while design flexibility is still cheap.

  • Lightweight components that replace metal parts
  • Complex shapes molded in one piece
  • Consistent quality across thousands of parts
  • Low cost per part once the tool is paid off
材料

High-Performance Engineering Plastics for Aerospace Applications

Aerospace materials must meet performance requirements for heat, aviation fluids and mechanical strength, and inside the cabin they must pass flame, smoke and toxicity rules such as FAR 25.853 for performance and safety. These are the resins aerospace manufacturers ask about most:

材料使用原因典型部件
PEEKStrength at high temperature, chemical resistanceBrackets, clips, bushings, metal replacements
PEI (Ultem)Inherent flame resistance, stiffnessCabin parts, electrical housings, ducts
PC and PC/ABSToughness and impact strengthCovers, bezels, panels
Nylon (PA66, glass-filled)Strength, wear resistanceClips, cable ties, gears
LSR siliconeFlexible, heat stableSeals and gaskets

Not every grade carries the flammability rating your program needs. Send the material specification with your drawings and we will confirm the grade, supplier certificate and moldability before quoting.

Polished steel multi-cavity injection mold tool
Mold Design and Tooling

Injection Mold Tooling and Engineering

Mold design comes first, because the injection mold decides part accuracy, surface finish and how long production can run. Our engineers review gating, venting, cooling and ejection, and run a free mold flow analysis to predict shrinkage, sink and warpage before tooling starts.

  • Aluminum injection mold tools for roughly 5,000 to 10,000 shots
  • Hardened steel injection mold tools for 100,000 to over 1,000,000 shots, suited to large quantities
  • Mold components machined to ±0.02 mm, with EDM for fine detail
  • Standard molded tolerance of ±0.1 mm, tighter on critical features

Learn more about our 注塑模具 process.

流程

Injection Molding Services for Complex Geometries

嵌入成型和包覆成型

插入成型 encapsulates threaded inserts, pins or contacts in one shot, which removes secondary assembly. 包覆成型 adds a soft-touch or sealing layer over a rigid substrate.

气体辅助成型与厚壁零件

Gas-assist molding hollows out thick sections to prevent sink and warpage and to reduce weight.

微型注塑

Micro injection molding produces small connector and sensor parts with fine features and tight tolerances.

液态硅橡胶成型

LSR molding makes seals, gaskets and grommets that stay flexible across a wide temperature range.

零件

Aerospace Parts and Plastic Molded Parts We Make

  • 内饰饰板、边框和座椅部件
  • 电气连接器主体和外壳
  • 电缆夹、扎带和线束支架
  • 航空电子设备机箱和外壳盖板
  • 通风口、风管配件和格栅
  • 无人机机身、螺旋桨护罩和电池盖
  • 密封件、垫片和衬套

These custom aerospace plastic parts are cost-effective components for aerospace manufacturing, where safety and performance both count.

质量

AS9100 Quality and Process Control for Aerospace Programs

Our quality management system is AS9100D and ISO 9001 certified, and every machine runs to documented settings. For aerospace and defense work we lock process settings after first article approval, record them for every lot, and supply material certificates, dimensional reports and lot traceability on request. Changes to resin, mold or process are only made with your approval.

从原型到生产

从原型到生产

Most programs start with printed or vacuum cast parts, move to an aluminum bridge tool for qualification parts, then switch to a steel production mold. Moving in that order keeps tooling spend low until the design is frozen, and our injection molding solutions cover each step.

获取报价

Get an Injection Molding Quote

Send your 3D model, resin specification, annual volume and finish. Our engineers will return tooling and part pricing, a mold flow report and lead time. Molded samples can be ready in as few as 5 business days from an aluminum tool.

获取即时报价
🔒 所有上传内容均安全且保密
与我们联系!
保证在24小时内及时回复
🔐 所有上传内容均安全保密
— 常见问题 —

常见问题

航空航天
什么是航空航天注塑成型?

这是将高性能热塑性塑料成型为航空航天部件的过程,例如客舱内饰件、连接器本体、卡扣以及用于飞机、航天器和无人机的外壳。与普通成型工艺相比,该工艺采用经过认证的树脂、固定的工艺参数以及有记录的检验程序,以确保每批产品均符合已批准的首件样品标准。

飞机成型过程中使用哪些塑料?

Common choices are PEEK for heat and chemical resistance, PEI (Ultem) for flame-resistant cabin and electrical parts, PC and PC/ABS for covers, nylon for clips and LSR for seals. The right grade depends on temperature, fluid exposure and flammability requirements.

Do your parts meet FAR 25.853 flammability rules?

Flammability depends on the resin grade and part thickness, not on the molding process alone. We mold FAR 25.853-rated grades when your specification calls for them and supply the resin certificate. Final compliance testing is usually done by your program or an approved lab.

How much does an aerospace injection mold cost?

Mold cost depends on part size, complexity, number of cavities and tool material. Aluminum molds cost less and suit thousands of parts, while hardened steel molds cost more but run hundreds of thousands of shots. We quote each tool from your 3D model after DFM review.

What tolerances can your molding hold?

Our standard molded tolerance is ±0.1 mm, with tighter tolerances possible on critical features depending on resin and geometry. Shrinkage varies by material, so we confirm achievable tolerances after mold flow analysis and before tooling starts.