Índice

Precisión Tuowei

¿Necesitas soluciones de mecanizado especializadas? El equipo de Tuowei Precision está a tu disposición para ayudarte con todas tus necesidades de fabricación. ¡Ponte en contacto con nosotros hoy mismo para solicitar un presupuesto para tus proyectos actuales o futuros!

Reaming - multi-fluted HSS reamer tool finishing a precision hole in steel block

Reaming is the finishing operation that turns a drilled hole into a precision hole. A reaming tool — a multi-fluted cutter with a slight lead chamfer — removes a small, controlled amount of stock from a pre-drilled hole, bringing it to exact size with a fine finish. If a drawing says Ø8 H7, a drill alone will not get you there; a reamer will. This guide defines the process, covers the tool types, and gives the working numbers: stock allowances, speeds, feeds and tolerances.

Reaming Definition

Reaming is a sizing and finishing process in which a rotary multi-edge cutting tool (the reamer) enlarges an existing hole by a small amount — typically 0.1–0.5 mm on diameter — to achieve accurate diameter (IT6–IT8), good roundness, and surface finish of Ra 0.4–1.6 µm. Because the reamer follows the existing hole, it improves size and finish but, like honing, cannot correct hole position — that is boring’s job.

Types of Reaming Tools

Reamer type Personaje Use case
Chucking (machine) reamer Straight or spiral flute, fixed size Standard production reaming on drill press, lathe, CNC
Hand reamer Long lead taper, square drive end Bench fitting; the long taper self-aligns in the hole
Adjustable reamer Sliding blades, size range Repair work, odd sizes; lower precision
Taper pin reamer 1:50 taper Taper pin holes in assemblies
Bridge/car reamer Long taper, aggressive Aligning structural bolt holes
Carbide / coated reamer Solid carbide or TiAlN coated Hardened steels, abrasive alloys, high-volume CNC

Spiral-flute reamers deserve a note: left-hand spiral pushes chips forward (through holes), right-hand spiral pulls chips back (blind holes), and spiral flutes bridge interrupted cuts like keyways without chatter.

Stock Allowance: The Number That Decides Everything

Diámetro del orificio Reaming allowance (on Ø)
Under 4 mm 0.1 mm
4–11 mm 0.15–0.2 mm
11–25 mm 0.2–0.3 mm
25–50 mm 0.3–0.5 mm

Too little stock and the reamer burnishes and rubs — glazed, work-hardened, undersize holes. Too much and it acts like a drill — oversize, poor finish, short tool life. For an H7 hole, the standard chain is: drill → (bore if position matters) → ream.

Speeds and Feeds by Material

Material Speed (HSS) Feed
Aluminio 25–30 m/min 0.3–0.8 mm/rev
Acero dulce 12–18 m/min 0.2–0.5 mm/rev
Alloy steel (treated) 6–10 m/min 0.15–0.3 mm/rev
Stainless (304/316) 5–8 m/min 0.15–0.3 mm/rev
Cast iron 10–15 m/min 0.3–0.6 mm/rev
Brass / bronze 20–30 m/min 0.3–0.8 mm/rev

Rule of thumb: ream at half the drilling speed and twice the drilling feed. High speed glazes and chatters; generous feed keeps the edges cutting. Carbide tooling roughly doubles these speeds.

What Tolerances Reaming Achieves

  • Diameter: IT7 routinely (e.g. Ø10 H7 = +0.015/0), IT6 with ground reamers in rigid setups
  • Roundness: 0.005–0.01 mm typical
  • Surface finish: Ra 0.4–1.6 µm (finer in aluminum with sharp tools and cutting oil)
  • Position: unchanged — the reamer follows the drilled hole. Use a floating holder so misalignment doesn’t bell-mouth the entry

Reaming vs Boring vs Honing

Factor Reaming Boring Honing
Corrects position No Sí No
Size accuracy IT6–IT8 IT6–IT9 IT5–IT6
Finish (Ra) 0.4–1.6 µm 0.8–3.2 µm 0.05–0.8 µm
Speed/cost Fastest, cheapest Flexible, slower Highest precision, costliest
Ideal para Standard fit holes (H7) Located/large/odd-size holes Sliding-seal bores

Solución de problemas

Problema Causa probable Corregir
Oversize hole Misalignment, built-up edge, excess speed Floating holder, lower speed, proper coolant
Undersize / glazed Too little stock, worn reamer Increase allowance, sharpen or replace
Poor finish Chip packing, high speed, low feed Spiral flutes, halve speed, double feed, cutting oil
Chatter / lobing Rigidness lacking, even flute spacing Shorter stickout, unequal-spacing reamer
Bell-mouthed entry Spindle/hole misalignment Floating reamer holder

Preguntas frecuentes

What is reaming in machining?

A finishing operation where a multi-fluted reaming tool removes 0.1–0.5 mm from a pre-drilled hole to deliver precise diameter (typically H7), roundness, and a fine Ra 0.4–1.6 µm finish.

What is the difference between drilling and reaming?

Drilling creates the hole but holds only ±0.05–0.1 mm with a rough finish; reaming refines that hole to within ~±0.01 mm with a near-polished wall. Drill first, ream second — a reamer cannot start its own hole.

Can a reamer fix hole position?

No. A reamer follows the existing hole’s axis. If true position matters, single-point bore the hole to correct location, then ream to final size.

How much material should be left for reaming?

Typically 0.15–0.3 mm on diameter for common sizes (see table above) — enough that every flute cuts, little enough that the reamer sizes rather than hogs.

Precision Reamed Holes From Tuowei Precision

H7 dowel fits, press-fit bearing bores, taper pin holes — reamed holes are routine callouts in the parts we ship daily through our Servicios de mecanizado CNC y mecanizado de precisión lines, including CNC turned parts with on-axis reamed bores. Upload your drawing — we quote within 24 hours with full dimensional reports available.

Retrato de un miembro del equipo de Tuowei Precision con un polo azul delante de unas máquinas CNC borrosas en la fábrica
Acerca del autor
Andy

Ingeniero de fabricación en tuoweiprecision

Escrito por Andy, ingeniero de fabricación en TUOWEI Precision. Andy está especializado en mecanizado CNC, fabricación de precisión e ingeniería de producción, y cuenta con experiencia práctica en el apoyo a proyectos que abarcan desde la creación rápida de prototipos hasta la producción a gran escala. Trabaja en estrecha colaboración con los equipos de ingeniería y fabricación para evaluar materiales, tolerancias, procesos de mecanizado y la facilidad de fabricación de los diseños. Sus artículos ofrecen información práctica y con base técnica para ayudar a ingenieros y compradores a tomar mejores decisiones de fabricación, optimizar la eficiencia de la producción y lograr una calidad constante de las piezas. Descubre las soluciones de mecanizado CNC y fabricación a medida de TUOWEI Precision para tu próximo proyecto.

Construyamos juntos el futuro

Colabora con Tuowei Precision para hacer realidad tu visión

Desde prototipos rápidos hasta la producción a gran escala, Tuowei Precision ofrece un mecanizado CNC fiable, con precisión y uniformidad en cada paso. Empieza tu proyecto hoy mismo.

Póngase en contacto con nosotros
Respuesta rápida garantizada en un plazo de 24 horas
🔐 Todas las cargas son seguras y confidenciales

Descubre ideas e innovación

Lee nuestras últimas guías sobre mecanizado CNC, materiales, acabados y tendencias del sector para tomar mejores decisiones de producción.

Póngase en contacto con nosotros
Respuesta rápida garantizada en un plazo de 24 horas
🔐 Todas las cargas son seguras y confidenciales