جدول المحتويات

دقة تووي

هل تحتاج إلى حلول متخصصة في مجال التصنيع الآلي؟ فريقنا في Tuowei Precision جاهز لمساعدتك في تلبية جميع احتياجاتك التصنيعية. تواصل معنا اليوم للحصول على عرض أسعار لمشاريعك الجارية أو المرتقبة!

Reaming - multi-fluted HSS reamer tool finishing a precision hole in steel block

Reaming is the finishing operation that turns a drilled hole into a precision hole. A reaming tool — a multi-fluted cutter with a slight lead chamfer — removes a small, controlled amount of stock from a pre-drilled hole, bringing it to exact size with a fine finish. If a drawing says Ø8 H7, a drill alone will not get you there; a reamer will. This guide defines the process, covers the tool types, and gives the working numbers: stock allowances, speeds, feeds and tolerances.

Reaming Definition

Reaming is a sizing and finishing process in which a rotary multi-edge cutting tool (the reamer) enlarges an existing hole by a small amount — typically 0.1–0.5 mm on diameter — to achieve accurate diameter (IT6–IT8), good roundness, and surface finish of Ra 0.4–1.6 µm. Because the reamer follows the existing hole, it improves size and finish but, like honing, cannot correct hole position — that is boring’s job.

Types of Reaming Tools

Reamer type الشخصية Use case
Chucking (machine) reamer Straight or spiral flute, fixed size Standard production reaming on drill press, lathe, CNC
Hand reamer Long lead taper, square drive end Bench fitting; the long taper self-aligns in the hole
Adjustable reamer Sliding blades, size range Repair work, odd sizes; lower precision
Taper pin reamer 1:50 taper Taper pin holes in assemblies
Bridge/car reamer Long taper, aggressive Aligning structural bolt holes
Carbide / coated reamer Solid carbide or TiAlN coated Hardened steels, abrasive alloys, high-volume CNC

Spiral-flute reamers deserve a note: left-hand spiral pushes chips forward (through holes), right-hand spiral pulls chips back (blind holes), and spiral flutes bridge interrupted cuts like keyways without chatter.

Stock Allowance: The Number That Decides Everything

قطر الثقب Reaming allowance (on Ø)
Under 4 mm 0.1 mm
4–11 mm 0.15–0.2 mm
11–25 mm 0.2–0.3 mm
25–50 mm 0.3–0.5 mm

Too little stock and the reamer burnishes and rubs — glazed, work-hardened, undersize holes. Too much and it acts like a drill — oversize, poor finish, short tool life. For an H7 hole, the standard chain is: drill → (bore if position matters) → ream.

Speeds and Feeds by Material

المواد Speed (HSS) التغذية
ألومنيوم 25–30 m/min 0.3–0.8 mm/rev
الفولاذ العادي 12–18 m/min 0.2–0.5 mm/rev
Alloy steel (treated) 6–10 m/min 0.15–0.3 mm/rev
Stainless (304/316) 5–8 m/min 0.15–0.3 mm/rev
Cast iron 10–15 m/min 0.3–0.6 mm/rev
Brass / bronze 20–30 m/min 0.3–0.8 mm/rev

Rule of thumb: ream at half the drilling speed and twice the drilling feed. High speed glazes and chatters; generous feed keeps the edges cutting. Carbide tooling roughly doubles these speeds.

What Tolerances Reaming Achieves

  • Diameter: IT7 routinely (e.g. Ø10 H7 = +0.015/0), IT6 with ground reamers in rigid setups
  • Roundness: 0.005–0.01 mm typical
  • Surface finish: Ra 0.4–1.6 µm (finer in aluminum with sharp tools and cutting oil)
  • Position: unchanged — the reamer follows the drilled hole. Use a floating holder so misalignment doesn’t bell-mouth the entry

Reaming vs Boring vs Honing

العامل Reaming Boring Honing
Corrects position لا يوجد نعم لا يوجد
Size accuracy IT6–IT8 IT6–IT9 IT5–IT6
Finish (Ra) 0.4–1.6 µm 0.8–3.2 µm 0.05–0.8 µm
Speed/cost Fastest, cheapest Flexible, slower Highest precision, costliest
الأفضل لـ Standard fit holes (H7) Located/large/odd-size holes Sliding-seal bores

استكشاف الأخطاء وإصلاحها

المشكلة السبب المحتمل تصحيح
Oversize hole Misalignment, built-up edge, excess speed Floating holder, lower speed, proper coolant
Undersize / glazed Too little stock, worn reamer Increase allowance, sharpen or replace
Poor finish Chip packing, high speed, low feed Spiral flutes, halve speed, double feed, cutting oil
Chatter / lobing Rigidness lacking, even flute spacing Shorter stickout, unequal-spacing reamer
Bell-mouthed entry Spindle/hole misalignment Floating reamer holder

الأسئلة الشائعة

What is reaming in machining?

A finishing operation where a multi-fluted reaming tool removes 0.1–0.5 mm from a pre-drilled hole to deliver precise diameter (typically H7), roundness, and a fine Ra 0.4–1.6 µm finish.

What is the difference between drilling and reaming?

Drilling creates the hole but holds only ±0.05–0.1 mm with a rough finish; reaming refines that hole to within ~±0.01 mm with a near-polished wall. Drill first, ream second — a reamer cannot start its own hole.

Can a reamer fix hole position?

No. A reamer follows the existing hole’s axis. If true position matters, single-point bore the hole to correct location, then ream to final size.

How much material should be left for reaming?

Typically 0.15–0.3 mm on diameter for common sizes (see table above) — enough that every flute cuts, little enough that the reamer sizes rather than hogs.

Precision Reamed Holes From Tuowei Precision

H7 dowel fits, press-fit bearing bores, taper pin holes — reamed holes are routine callouts in the parts we ship daily through our خدمات التصنيع الآلي باستخدام الحاسب الآلي الرقمي و التصنيع الآلي الدقيق lines, including CNC turned parts with on-axis reamed bores. Upload your drawing — we quote within 24 hours with full dimensional reports available.

صورة لأحد أعضاء فريق «تووي بريسيشن» يرتدي قميص بولو أزرق أمام آلات CNC غير واضحة المعالم في المصنع
نبذة عن المؤلف
آندي

مهندس تصنيع في شركة tuoweiprecision

بقلم آندي، مهندس تصنيع في شركة TUOWEI Precision. يتخصص آندي في التصنيع باستخدام الحاسب الآلي (CNC) والتصنيع الدقيق وهندسة الإنتاج، ويتمتع بخبرة عملية في دعم المشاريع بدءًا من النماذج الأولية السريعة وصولًا إلى الإنتاج على نطاق واسع. وهو يعمل عن كثب مع فرق الهندسة والتصنيع لتقييم المواد والتفاوتات المسموح بها وعمليات التصنيع وقابلية التصميم للتصنيع. تقدم مقالاته رؤى عملية ومستندة إلى المعرفة التقنية لمساعدة المهندسين والمشترين على اتخاذ قرارات تصنيع أفضل، وتحسين كفاءة الإنتاج، وتحقيق جودة متسقة للأجزاء. اكتشف حلول التصنيع باستخدام الحاسب الآلي (CNC) والتصنيع المخصص التي تقدمها TUOWEI Precision لمشروعك القادم.

لنبني المستقبل معًا

تعاون مع شركة «تووي بريسيجن» لتحويل رؤيتك إلى واقع

بدءًا من النماذج الأولية السريعة وصولاً إلى الإنتاج القابل للتوسع، تقدم شركة Tuowei Precision خدمات تصنيع موثوقة باستخدام الحاسب الآلي (CNC) تتسم بالدقة والاتساق في كل خطوة. ابدأ مشروعك اليوم.

تواصل معنا!
نضمن الرد السريع في غضون 24 ساعة
🔐 جميع التحميلات آمنة وسرية

استكشف الرؤى والابتكار

اقرأ أحدث أدلةنا حول التصنيع باستخدام الحاسب الآلي (CNC) والمواد والتشطيب واتجاهات الصناعة لاتخاذ قرارات إنتاجية أفضل.

تواصل معنا!
نضمن الرد السريع في غضون 24 ساعة
🔐 جميع التحميلات آمنة وسرية