目次

卓偉精密

専門的な機械加工ソリューションをお探しですか?Tuowei Precisionのチームが、お客様のあらゆる製造ニーズにお応えします。現在進行中または今後予定されているプロジェクトのお見積もりについては、ぜひ今すぐお問い合わせください!

Reaming - multi-fluted HSS reamer tool finishing a precision hole in steel block

Reaming is the finishing operation that turns a drilled hole into a precision hole. A reaming tool — a multi-fluted cutter with a slight lead chamfer — removes a small, controlled amount of stock from a pre-drilled hole, bringing it to exact size with a fine finish. If a drawing says Ø8 H7, a drill alone will not get you there; a reamer will. This guide defines the process, covers the tool types, and gives the working numbers: stock allowances, speeds, feeds and tolerances.

Reaming Definition

Reaming is a sizing and finishing process in which a rotary multi-edge cutting tool (the reamer) enlarges an existing hole by a small amount — typically 0.1–0.5 mm on diameter — to achieve accurate diameter (IT6–IT8), good roundness, and surface finish of Ra 0.4–1.6 µm. Because the reamer follows the existing hole, it improves size and finish but, like honing, cannot correct hole position — that is boring’s job.

Types of Reaming Tools

Reamer type キャラクター Use case
Chucking (machine) reamer Straight or spiral flute, fixed size Standard production reaming on drill press, lathe, CNC
Hand reamer Long lead taper, square drive end Bench fitting; the long taper self-aligns in the hole
Adjustable reamer Sliding blades, size range Repair work, odd sizes; lower precision
Taper pin reamer 1:50 taper Taper pin holes in assemblies
Bridge/car reamer Long taper, aggressive Aligning structural bolt holes
Carbide / coated reamer Solid carbide or TiAlN coated Hardened steels, abrasive alloys, high-volume CNC

Spiral-flute reamers deserve a note: left-hand spiral pushes chips forward (through holes), right-hand spiral pulls chips back (blind holes), and spiral flutes bridge interrupted cuts like keyways without chatter.

Stock Allowance: The Number That Decides Everything

穴径 Reaming allowance (on Ø)
Under 4 mm 0.1 mm
4–11 mm 0.15–0.2 mm
11–25 mm 0.2–0.3 mm
25–50 mm 0.3–0.5 mm

Too little stock and the reamer burnishes and rubs — glazed, work-hardened, undersize holes. Too much and it acts like a drill — oversize, poor finish, short tool life. For an H7 hole, the standard chain is: drill → (bore if position matters) → ream.

Speeds and Feeds by Material

素材 Speed (HSS) フィード
アルミニウム 25–30 m/min 0.3–0.8 mm/rev
軟鋼 12–18 m/min 0.2–0.5 mm/rev
Alloy steel (treated) 6–10 m/min 0.15–0.3 mm/rev
Stainless (304/316) 5–8 m/min 0.15–0.3 mm/rev
Cast iron 10–15 m/min 0.3–0.6 mm/rev
Brass / bronze 20–30 m/min 0.3–0.8 mm/rev

Rule of thumb: ream at half the drilling speed and twice the drilling feed. High speed glazes and chatters; generous feed keeps the edges cutting. Carbide tooling roughly doubles these speeds.

What Tolerances Reaming Achieves

  • Diameter: IT7 routinely (e.g. Ø10 H7 = +0.015/0), IT6 with ground reamers in rigid setups
  • Roundness: 0.005–0.01 mm typical
  • Surface finish: Ra 0.4–1.6 µm (finer in aluminum with sharp tools and cutting oil)
  • Position: unchanged — the reamer follows the drilled hole. Use a floating holder so misalignment doesn’t bell-mouth the entry

Reaming vs Boring vs Honing

ファクター Reaming Boring Honing
Corrects position いいえ はい いいえ
Size accuracy IT6–IT8 IT6–IT9 IT5–IT6
Finish (Ra) 0.4–1.6 µm 0.8–3.2 µm 0.05–0.8 µm
Speed/cost Fastest, cheapest Flexible, slower Highest precision, costliest
こんな方に最適 Standard fit holes (H7) Located/large/odd-size holes Sliding-seal bores

トラブルシューティング

問題 考えられる原因 修正
Oversize hole Misalignment, built-up edge, excess speed Floating holder, lower speed, proper coolant
Undersize / glazed Too little stock, worn reamer Increase allowance, sharpen or replace
Poor finish Chip packing, high speed, low feed Spiral flutes, halve speed, double feed, cutting oil
Chatter / lobing Rigidness lacking, even flute spacing Shorter stickout, unequal-spacing reamer
Bell-mouthed entry Spindle/hole misalignment Floating reamer holder

よくある質問

What is reaming in machining?

A finishing operation where a multi-fluted reaming tool removes 0.1–0.5 mm from a pre-drilled hole to deliver precise diameter (typically H7), roundness, and a fine Ra 0.4–1.6 µm finish.

What is the difference between drilling and reaming?

Drilling creates the hole but holds only ±0.05–0.1 mm with a rough finish; reaming refines that hole to within ~±0.01 mm with a near-polished wall. Drill first, ream second — a reamer cannot start its own hole.

Can a reamer fix hole position?

No. A reamer follows the existing hole’s axis. If true position matters, single-point bore the hole to correct location, then ream to final size.

How much material should be left for reaming?

Typically 0.15–0.3 mm on diameter for common sizes (see table above) — enough that every flute cuts, little enough that the reamer sizes rather than hogs.

Precision Reamed Holes From Tuowei Precision

H7 dowel fits, press-fit bearing bores, taper pin holes — reamed holes are routine callouts in the parts we ship daily through our CNC加工サービス そして 精密機械加工 lines, including CNC turned parts with on-axis reamed bores. Upload your drawing — we quote within 24 hours with full dimensional reports available.

工場内のぼやけたCNC工作機械を背景に、青いポロシャツを着たトゥオウェイ・プレシジョン社のチームメンバーの肖像
著者について
アンディ

tuoweiprecision社の製造エンジニア

執筆:TUOWEI Precisionの製造エンジニア、アンディ。. アンディは、CNC加工、精密製造、生産工学を専門としており、ラピッドプロトタイピングから本格生産に至るまでのプロジェクト支援において、実務経験を有しています。彼は、エンジニアリングチームや製造チームと緊密に連携し、材料、公差、加工プロセス、および設計の製造適性を評価しています。 彼の記事は、実用的かつ技術的な知見に裏打ちされた洞察を提供し、エンジニアや購買担当者がより適切な製造上の意思決定を行い、生産効率を最適化し、一貫した部品品質を実現できるよう支援しています。次回のプロジェクトには、TUOWEI PrecisionのCNC加工およびカスタム製造ソリューションをご検討ください。.

さあ、次の時代を共に築きましょう

Tuowei Precisionと提携し、お客様のビジョンを形にしましょう

ラピッドプロトタイピングから量産に至るまで、Tuowei Precisionは、あらゆる工程において精度と一貫性を兼ね備えた信頼性の高いCNC加工を提供します。今すぐプロジェクトを始めましょう。.

お問い合わせ
24時間以内の迅速な対応をお約束します
🔐 すべてのアップロードは安全かつ機密です。

インサイト&イノベーション

CNC加工、材料、仕上げ、業界の動向に関する最新のガイドをご覧いただき、より適切な生産判断を行ってください。

お問い合わせ
24時間以内の迅速な対応をお約束します
🔐 すべてのアップロードは安全かつ機密です。