Índice

Precisión Tuowei

¿Necesitas soluciones de mecanizado especializadas? El equipo de Tuowei Precision está a tu disposición para ayudarte con todas tus necesidades de fabricación. ¡Ponte en contacto con nosotros hoy mismo para solicitar un presupuesto para tus proyectos actuales o futuros!

CNC lathe turret with turning, boring and grooving lathe cutting tools

Lathe cutting tools are the single-point and multi-point tools that remove metal from a rotating workpiece. The core set is turning, facing, boring, grooving, parting, threading and drilling tools, plus forming and chamfering tools for special shapes. Most modern turning uses carbide inserts clamped in steel holders rather than ground tool bits.

Respuesta rápida: Pick the tool by the operation first (outside diameter, face, bore, groove, thread or cut-off), then by insert shape and nose radius, then by tool material for the workpiece. A turning tool with an 80° insert and a 0.8 mm nose radius covers most general work on steel and aluminum.

This guide is written from the shop floor. It explains what each tool does, how to read an insert code, which tool material suits which metal, and the setup mistakes that cause chatter, bad finishes and broken inserts.

What Are Lathe Cutting Tools?

A lathe spins the workpiece while a stationary tool moves along or across it. That is the opposite of milling, where the tool spins. Because the tool does not rotate, most lathe tools have a single edge, which is why turning tools are often called single-point tools. Drills, reamers and taps used in the tailstock or turret are the exceptions, since they cut with more than one edge.

There are two broad families of metal lathe cutting tools. Ground tool bits are square blanks of high-speed steel (HSS) that the machinist sharpens to the needed shape. Indexable tools hold a replaceable insert in a steel holder. When an edge wears, you rotate the insert to a fresh corner instead of regrinding. On CNC lathes, indexable tooling is the default because it gives repeatable tool positions and faster changeovers. The tool post (or the turret on a CNC lathe), mounted on the carriage’s compound slide, is the component that holds the cutting tools.

It also helps to separate two terms that searches often mix up. A machine tool is the machine itself: the lathe, mill, drill press or grinder. A cutting tool is what the machine holds to remove material. This article covers cutting tools for lathes.

The 12 Main Types of Lathe Tools

The table below lists the tools you will find on almost every manual or CNC lathe, what each one does, and where it goes on the part.

Herramienta Funcionamiento Uso habitual
Turning tool (RH/LH) Reduces outside diameter Shafts, pins, general OD work
Facing tool Cuts a flat end face square to the axis Squaring stock, setting length
Boring bar Enlarges and finishes an existing hole Accurate internal diameters
Grooving tool Cuts a narrow channel on OD, ID or face O-ring grooves, snap-ring seats
Parting (cut-off) tool Separates the finished part from bar stock End of every bar-fed part
Threading tool Cuts external or internal threads Bolts, fittings, threaded bores
Drill Makes the first hole from the tailstock or turret Center holes, through holes
Center drill Makes a short, conical start hole Spotting for drills or live centers
Reamer Finishes a drilled hole to size Close-tolerance bores
Chamfering tool Breaks sharp edges at an angle Edge breaks, thread lead-ins
Form tool Cuts a profile in one plunge Radii, special contours in volume
Knurling tool Presses a diamond or straight pattern Grip surfaces on handles and knobs

A note on knurling: a knurling tool forms the surface by pressing it, rather than cutting chips. It sits on the lathe with the cutting tools, but it works on a different principle and needs a rigid setup and plenty of lubricant.

Diagram showing where each type of lathe tool cuts on a turned part

Turning and Facing Tools

Turning tools come in right-hand and left-hand versions. A right-hand tool cuts while moving toward the headstock, which is the most common direction. Facing usually uses the same holder with an insert that has enough clearance to cut across the end of the part. Use an 80° rhombic or trigon insert when you need strength for roughing, and a sharper 55° or 35° insert when you need to reach into profiles.

Boring Bars

A boring bar is a long, slim holder that reaches inside a hole. Its stick-out is the biggest factor in chatter. A useful rule: keep overhang under about four times the bar diameter for steel bars, and switch to carbide or damped bars when you need more reach. Smaller nose radii also reduce chatter in bores.

Grooving and Parting Tools

These tools plunge straight into the part, so they work with a narrow blade that is weak sideways. Set them exactly on center height and square to the axis. Off-center parting tools leave a pip on the part and break blades. Use the shortest blade extension that still reaches the center of the bar.

Threading Tools

A threading insert has the thread profile ground on its tip, such as 60° for Unified and metric threads or 55° for Whitworth. The tool moves in a straight line along the part while the lathe synchronizes the feed to spindle rotation. Several light passes build the thread depth. For the common sizes and pitches, see a thread size chart before you set the pitch.

How to Read an Insert Code (CNMG 120408 Explained)

Indexable inserts follow ISO 1832, so the code tells you the shape and size before you open the box. Taking CNMG 120408 as the example:

Puesto Letter or number Significado
1 C Shape: 80° rhombic
2 N Clearance angle: 0° (negative insert, used on both sides)
3 M Tolerance class
4 G Chipbreaker on both faces, with a center hole
5 12 Edge length, about 12 mm
6 04 Thickness, 4.76 mm
7 08 Nose radius, 0.8 mm

Other common shapes are D (55°), V (35°), T (60° triangle), W (80° trigon), S (90° square) and R (round). Stronger, blunter shapes rough better; sharper shapes profile better. Negative inserts (N) give two-sided use and a stronger edge. Positive inserts (C, P) cut with less force, which suits small parts, boring bars and soft metals.

CNMG 120408 turning insert code explained

Cutting Tool Materials: Which One for Which Metal?

Cutting tool materials decide how fast you can cut and which metals you can cut at all. These are the ones you will meet on a lathe.

Tool material Ideal para Ten cuidado con
High-speed steel (HSS, M2) Manual lathes, form tools, low speeds, small shops Softens if overheated; low cutting speed
Cobalt HSS (M42) Tougher steels, interrupted cuts with HSS Still slower than carbide
Uncoated carbide Aluminum, brass, plastics Built-up edge in sticky metals
Coated carbide (TiN, TiAlN, Al2O3) Steel, stainless and cast iron, most CNC turning Brittle in heavy interruptions
Cermet Fine finishing of steel at high speed Weak in roughing and interrupted cuts
Ceramic Cast iron and heat-resistant alloys at very high speed Needs very rigid machines
CBN Hardened steel (roughly 45 HRC and above) Expensive; poor in soft steel
PCD (diamond) Aluminum, copper, composites, plastics Cannot cut steel (reacts with iron)

Our default is coated carbide for steel and stainless, polished uncoated or PCD for aluminum, and CBN when we turn hardened parts such as heat-treated D2 tool steel. HSS still earns its place for one-off form tools and on manual machines, where low speeds suit it.

Tool Geometry That Changes Your Results

Most guides list angles without saying what they do. Here is what each one changes in practice.

  • Rake angle: a positive rake makes a sharper edge that cuts with less force. Negative rake makes a stronger edge for hard materials and interrupted cuts.
  • Relief (clearance) angle: keeps the tool flank from rubbing the part. Too little relief causes rubbing and heat; too much weakens the edge.
  • Nose radius: a larger radius gives a stronger edge and a better finish at a given feed, but it pushes harder against the part and can cause chatter on slender work.
  • Lead (approach) angle: spreads the cut over a longer edge, which helps tool life in roughing.
  • Center height: the tip must sit on the spindle center line. A tool set high rubs; a tool set low digs in and leaves a pip when facing.

As a starting point for HSS tool bits on mild steel, many shops grind about 8° to 12° back rake and 6° to 8° relief. Treat those as starting values and adjust for the material. With inserts, the geometry is built in, so you choose it through the insert and holder rather than the grinder.

Chip Control and Common Tool Problems

Long, stringy chips wrap around the part and can mark the finish or injure the operator. Chipbreakers in the insert, the right feed and the right depth of cut break chips into short curls. If chips stay long, raise the feed slightly or pick an insert with a tighter chipbreaker for finishing.

These are the problems we see most often, with the usual cause:

  • Rapid flank wear: cutting speed too high, or the wrong grade for the material.
  • Crater wear on the top face: heat and chemical wear in steel at high speed; use a coated grade.
  • Built-up edge: material welding to the tip in aluminum or low-carbon steel; raise speed, use a sharper, polished insert and coolant.
  • Chipping: interrupted cuts or vibration; use a tougher grade, a stronger shape and less overhang.
  • Chatter marks: too much stick-out, a large nose radius on a slender part, or a worn insert.
  • Poor finish: feed too high for the nose radius. Theoretical roughness rises with the square of the feed and falls as the nose radius grows.

Tool life testing is standardized in ISO 3685 if you need to compare grades properly rather than by feel.

How to Choose Lathe Tools for a Job

  1. List the operations on the drawing. Outside diameters, faces, bores, grooves, threads and cut-off each need their own tool.
  2. Choose the holder and insert shape. Use strong 80° shapes for roughing, 55° or 35° for profiling and undercuts.
  3. Match the tool material to the workpiece. Use the table above as your first filter.
  4. Pick the nose radius for the finish. 0.4 mm for fine detail and slender parts, 0.8 mm for general work, 1.2 mm for heavy roughing.
  5. Set the cutting data from the insert supplier. Start in the middle of the recommended range, then adjust for the machine’s rigidity.
  6. Minimize overhang and check center height before the first cut.

On a CNC lathe, the choice of lathe tools also decides cycle time. Fewer tool changes, fewer separate finishing passes and good chip control often save more time than chasing higher cutting speeds. Our CNC turning service plans the tool list this way for every part.

Wood Lathe Tools vs Metal Lathe Tools

Many searches for lathe tools return woodturning gouges, skews and scrapers. Those are hand-held tools rested on a tool rest, and they cut wood by shearing the fibers. Metal lathe cutting tools are clamped rigidly in a tool post or turret and cut with fixed geometry. The two are not interchangeable, so make sure a tool listing says which type of lathe it is meant for.

FAQ: Lathe Tools and Types of Cutting Tools

What are the different lathe tools called?

The main lathe tools are turning, facing, boring, grooving, parting, threading, chamfering and form tools, plus drills, center drills and reamers used from the tailstock or turret. Knurling tools also sit on lathes, but they press a pattern rather than cut. Most modern lathes use carbide inserts in steel holders.

What are 10 common types of cutting tools?

Ten common cutting tools are turning tools, boring bars, parting tools, grooving tools, threading tools, drills, reamers, taps, end mills and face mills. The first five are typical lathe tools; end mills and face mills belong on milling machines. Each removes material by shearing it away in chips.

What are the 7 basic types of machine tools?

The seven basic machine tools usually listed are the lathe, drill press, milling machine, shaper, planer, grinder and power saw. Each holds and moves a cutting tool or workpiece in a different way. Modern CNC lathes and machining centers combine several of these operations in one machine.

What is the best cutting tool material for steel?

Coated carbide is the best general choice for turning steel on CNC lathes because it holds its edge at high cutting speeds. HSS suits low-speed manual work and custom form tools. For hardened steel above roughly 45 HRC, CBN inserts are usually the better option, despite their higher price.

How do I stop chatter on a lathe?

Reduce tool overhang first, then check that the insert is sharp and on center. A smaller nose radius, a sharper positive insert, a lower spindle speed and a rigid workholding setup all help. In bores, use the largest and shortest boring bar that fits, or switch to a carbide or damped bar.

Getting the Right Tooling Plan for Turned Parts

Good turning starts with the right tool for each operation, a sensible insert shape, the correct tool material for the metal, and a rigid, on-center setup. Get those four right and most chatter, poor finish and broken-insert problems disappear.

If you have turned or mill-turned parts to make, our engineers review the drawing, plan the tooling and quote the job. For the process side, see what CNC turning is and how it works, or read Cómo funciona el mecanizado CNC. When you are ready, Sube tu dibujo para recibir un presupuesto o visita Precisión Tuowei.

Fuentes y lecturas recomendadas – International Organization for Standardization, ISO 1832 Indexable inserts for cutting tools: Designation: iso.org – International Organization for Standardization, ISO 3685 Tool-life testing with single-point turning tools: iso.org

Insert grades, cutting speeds and tool angles are typical starting points. Confirm them with your tool supplier’s data for the exact grade and workpiece material.

Angles, nose radii and overhang ratios are typical starting values. Always follow the insert manufacturer’s cutting data for your grade and machine.

Retrato de un miembro del equipo de Tuowei Precision con un polo azul delante de unas máquinas CNC borrosas en la fábrica
Acerca del autor
Andy

Ingeniero de fabricación en tuoweiprecision

Escrito por Andy, ingeniero de fabricación en TUOWEI Precision. Andy está especializado en mecanizado CNC, fabricación de precisión e ingeniería de producción, y cuenta con experiencia práctica en el apoyo a proyectos que abarcan desde la creación rápida de prototipos hasta la producción a gran escala. Trabaja en estrecha colaboración con los equipos de ingeniería y fabricación para evaluar materiales, tolerancias, procesos de mecanizado y la facilidad de fabricación de los diseños. Sus artículos ofrecen información práctica y con base técnica para ayudar a ingenieros y compradores a tomar mejores decisiones de fabricación, optimizar la eficiencia de la producción y lograr una calidad constante de las piezas. Descubre las soluciones de mecanizado CNC y fabricación a medida de TUOWEI Precision para tu próximo proyecto.

Construyamos juntos el futuro

Colabora con Tuowei Precision para hacer realidad tu visión

Desde prototipos rápidos hasta la producción a gran escala, Tuowei Precision ofrece un mecanizado CNC fiable, con precisión y uniformidad en cada paso. Empieza tu proyecto hoy mismo.

Póngase en contacto con nosotros
Respuesta rápida garantizada en un plazo de 24 horas
🔐 Todas las cargas son seguras y confidenciales

Descubre ideas e innovación

Lee nuestras últimas guías sobre mecanizado CNC, materiales, acabados y tendencias del sector para tomar mejores decisiones de producción.

Póngase en contacto con nosotros
Respuesta rápida garantizada en un plazo de 24 horas
🔐 Todas las cargas son seguras y confidenciales