Accueil » Blogs » Blog » What Is TPE? TPE vs TPR Material, Shore A Hardness & Overmolding Guide

What Is TPE? TPE vs TPR Material, Shore A Hardness & Overmolding Guide

Table des matières

Précision Tuowei

Vous avez besoin de solutions d'usinage spécialisées ? L'équipe de Tuowei Precision est là pour répondre à tous vos besoins en matière de fabrication. Contactez-nous dès aujourd'hui pour obtenir un devis concernant vos projets en cours ou à venir !

Overmolded TPE material grips on rigid plastic handles

What is TPE? TPE, or thermoplastic elastomer, is a rubber-like plastic that stretches and recovers like rubber but melts and molds like a thermoplastic. Because it needs no vulcanizing, it can be injection molded fast, recycled as regrind, and overmolded directly onto rigid plastic parts. TPR (thermoplastic rubber) is one type of TPE, usually based on SBS.

Réponse rapide : TPE is a family of soft, flexible plastics, typically Shore 0A to about 60D. TPR is a styrenic TPE and a subset of the family, so every TPR is a TPE but not every TPE is a TPR. Choose TPE for soft-touch grips, seals and overmolded parts; choose silicone when you need high heat resistance or the lowest compression set.

The confusion between TPE, TPR, TPU and silicone causes real sourcing mistakes, mostly because suppliers use the names loosely. This guide sorts out the terms, then covers properties, hardness, safety, cost drivers and the design rules that decide whether an overmolded grip stays bonded.

What Is TPE Material?

TPE material combines two kinds of molecular structure. Hard segments act like physical cross-links at room temperature, which is why the part springs back after stretching. When heated, those hard segments soften, so the material flows into a mold. When it cools, they lock again. Conventional rubber is chemically cross-linked by vulcanization and cannot be remelted; that is the key difference.

In practice this gives manufacturers three advantages over thermoset rubber:

  • Faster processing. Standard injection molding cycles instead of long cure times.
  • Recycling. Sprues, runners and rejected parts can be reground and reused within the grade’s limits.
  • Two-shot and overmolding. TPE can bond to a rigid substrate in the mold, with no glue.

The trade-offs are lower heat resistance and higher compression set than good thermoset rubbers. We cover both below, because they decide most material failures we see.

The 6 Types of Thermoplastic Elastomers

ISO 18064 groups thermoplastic elastomers into families by chemistry. Knowing the family matters more than the trade name, because it predicts heat, oil and bonding behavior.

ISO codeFamilyCommon namesTypical strengthsUtilisations courantes
TPS (TPE-S)Styrenic block copolymersSBS, SEBS, TPRVery soft grades, good feel, easy overmoldingGrips, toys, seals, consumer goods
TPO (TPE-O)Olefinic blendsTPOLow cost, good weatheringAutomotive bumpers and trim
TPV (TPE-V)Vulcanized PP/EPDMSantoprene typeBetter heat and compression setAutomotive seals, hoses, gaskets
TPU (TPE-U)PolyuréthaneTPUToughness, abrasion and tear resistanceCable jackets, phone cases, wheels
TPC (TPE-E)CopolyesterCOPEHigher heat and chemical resistanceCV boots, bellows, industrial parts
TPA (TPE-A)PolyamidePEBA, COPALight weight, energy returnSports shoes, medical tubing

When a supplier quotes “TPE” without a family, ask which one. A styrenic grade and a copolyester grade at the same Shore A hardness behave very differently in heat and oil.

TPE vs TPR: Are They the Same?

No. TPR is a subset of TPE. Thermoplastic rubber is the trade term for styrenic TPEs, most often based on SBS (styrene-butadiene-styrene). So the honest comparison is SBS-based TPR against the wider TPE family, and especially against SEBS-based TPE, its closest relative.

PropriétéTPR material (SBS-based)TPE à base de SEBS
ChimieStyrene-butadiene-styreneHydrogenated midblock (styrene-ethylene-butylene-styrene)
UV and ozone resistanceFair; can yellow and crack outdoorsBon
Heat resistanceInférieurPlus élevé
RessentirRubbery, slightly tackySmooth, silky soft-touch
CoûtUsually lowerUsually higher
Utilisations courantesShoe soles, toys, budget gripsMedical, food-contact, premium grips, outdoor parts

Many TPE vs TPR guides contradict each other on which one is “harder.” The truth is that hardness depends on the compound, not the label. Both TPR and TPE are sold from very soft to fairly firm grades, so always specify Shore A hardness rather than the name.

TPE vs TPR material examples: TPR shoe sole and SEBS grip

Shore A Hardness: How Soft Is Your TPE Material?

Hardness of soft materials is measured with a durometer under ASTM D2240. The Shore A scale covers most TPE grades; very soft gels use Shore 00, and stiff grades move to Shore D. Approximate everyday comparisons help when you specify a grip:

Shore hardnessFeels like (approximate)Typical TPE use
20A to 30ARubber band, soft gel insoleCushions, soft-touch pads
40A to 50APencil eraserToothbrush grips, tool handles
60A to 70ACar tire treadSeals, gaskets, bumpers
80A to 90AShoe heelFeet, wheels, cable sleeves
95A and up (to Shore D)Shopping cart wheel, hard rubberRollers, stiff boots, jackets

Our rule of thumb for overmolded grips is 40A to 60A. Softer feels good but wears and picks up dirt; harder transmits vibration and feels like plastic.

Shore A hardness scale for TPE material with everyday examples

Key Properties of TPE

TPE material properties vary by family and grade, so treat these as directions to check on the datasheet rather than fixed numbers.

  • Elasticity: stretches and recovers; elongation at break often runs several hundred percent in soft grades.
  • Compression set: higher than vulcanized rubber or silicone. Under constant compression and heat, a seal made of thermoplastic elastomer slowly takes a permanent set. TPV performs best among TPEs here.
  • Résistance à la chaleur : styrenic grades lose properties at lower temperatures than TPV, TPC or silicone. Check the continuous-use temperature for your part, not just the melting range.
  • Chemical and oil resistance: good against water, acids and alkalis in most grades; styrenic TPEs swell in oils and fuels, while TPC and TPV handle oils better.
  • Isolation électrique : good, which is why TPE material is common in cable jackets and plugs.
  • Colorability and feel: easy to color and texture for soft-touch surfaces.

TPE vs Silicone vs TPU vs Rubber

Buyers usually choose between these four. The table summarizes where each one wins.

FacteurTPE (styrenic)SiliconeTPUThermoset rubber (EPDM, NBR)
ProcessingInjection molding, fastLSR molding or compression, slowerInjection molding, needs dryingCompression or transfer molding, cure time
Recyclable scrapOuiNonOuiNon
Heat resistanceInférieurLe plus élevéMoyenMoyen à élevé
Compression setJusteExcellentPassable à bonBon
Résistance à l'abrasionJusteJusteExcellentBon
Overmolding onto plasticsFacilePossible with special gradesGood on PC/ABSNot in the same mold
Coût relatifFaible à moyenHautMoyenMoyen

TPE vs silicone is the most common question. Silicone wins on heat, cold flexibility and long-term sealing; TPE wins on cost, cycle time and the ability to overmold onto PP, ABS or PC in one tool.

Is TPE Safe? Toxicity, Food Contact and Medical Use

TPE material is generally considered non-toxic and is widely used in baby products, kitchen tools and medical devices. Most compounds are free of latex and do not need the plasticizers found in flexible PVC. That said, “TPE” is not a safety certification. What matters is the specific grade and its paperwork:

  • Food contact: ask for the FDA and EU food-contact compliance statement for the exact grade.
  • Médical : look for USP Class VI and ISO 10993 biocompatibility test data on the grade, and confirm the supplier’s change-control policy.
  • Produits de consommation : check REACH and RoHS declarations, and any toy-safety requirements for children’s items.

Cheap TPR grades with unknown fillers or oils are where odor and safety complaints usually come from. Specify the grade, not just the material type.

Overmolding With TPE: Design Rules That Prevent Peeling

This is where most parts made from thermoplastic elastomers fail, and where most guides stop short. TPE bonds chemically to some substrates and not to others, so material pairing comes first.

Rigid substrateBonding with standard SEBS TPEWhat to do
PPBonStandard grades bond well
ABS, PC, PC/ABSPoor with standard gradesUse a modified “ABS/PC-bonding” TPE grade
Nylon (PA6, PA66)MauvaisUse PA-bonding grades and dry the nylon
MétalAucunUse mechanical locks or adhesive primers

Then design for the bond:

  1. Keep TPE walls even, roughly 1 mm to 3 mm for most grips; thick sections sink and cool unevenly.
  2. Add mechanical interlocks, such as through-holes or undercuts the TPE can flow into, when chemical bonding is weak.
  3. End the TPE edge in a groove or against a shoulder so it cannot be peeled up during use.
  4. Avoid thin TPE feather edges, which flash and lift.
  5. Mold the substrate first and keep it clean and warm for the second shot; contamination and cold substrates weaken the bond.

Notre overmolding service runs substrate and TPE trials together for this reason, and our guide to surmoulage vs moulage par insertion explains when each process makes more sense.

Processing Tips for Molding TPE

  • Dry when the family needs it. TPU and TPC absorb moisture and must be dried; most styrenic TPEs do not need drying unless the supplier says so.
  • Control melt temperature. Overheating degrades styrenic grades and causes odor and discoloration; follow the datasheet range.
  • Expect anisotropic shrinkage. TPE shrinks differently along and across the flow, so plan gate location with the tooling engineer.
  • Vent well. Soft materials flash easily if vents and parting lines are not tight.

Defects such as sink marks, flash and short shots follow the same causes as in other plastics; see our guide to défauts de moulage par injection.

What Drives TPE Cost?

Raw price per kilogram changes with oil markets and region, so a fixed number would be misleading. These factors move part cost more than the base price:

  • Family and grade: TPR and TPO are usually cheapest; SEBS, TPU, TPC and medical grades cost more.
  • Bonding grades: modified grades for ABS, PC or nylon carry a premium.
  • Tooling: two-shot molds cost more than single-shot tools but remove assembly labor.
  • Scrap and regrind: recyclable runners lower the effective material cost.

FAQ About TPE and TPR Material

Is TPE plastic or rubber?

TPE is technically a plastic, but it behaves like rubber. It stretches and recovers like an elastomer, yet it melts and can be remolded like a thermoplastic. That combination is why it is called a thermoplastic elastomer and why it suits injection molding and overmolding better than conventional vulcanized rubber.

Which is safer, TPE or silicone?

Both are considered safe when you use certified grades. Medical-grade silicone has the longer track record in implants and high-heat use, and it tolerates sterilization better. TPE is safe for many food-contact and medical uses when the specific grade carries FDA, USP Class VI or ISO 10993 data. Always check the grade.

What are the disadvantages of TPE?

TPE has lower heat resistance and higher compression set than silicone or vulcanized rubber, so seals under constant pressure and heat can lose sealing force. Styrenic grades swell in oils and fuels. Some grades feel tacky or attract dust, and bonding to ABS, PC or nylon needs special modified grades.

Are TPE and TPR the same?

No. TPR is a type of TPE. TPR usually means a styrenic compound based on SBS, while TPE covers six families, including SEBS, TPV, TPU and copolyester grades. TPR is generally cheaper but has weaker UV and heat resistance than SEBS-based TPE. Specify the family and hardness, not just the name.

What is TPE used for?

TPE is used for soft-touch grips on tools and toothbrushes, seals and gaskets, cable jackets, phone cases, footwear, medical tubing, baby products, and automotive trim and seals. Its biggest advantage in manufacturing is overmolding, where a soft TPE layer is molded directly onto a rigid plastic part in one tool.

Choosing the Right TPE for Your Part

Start with the job, not the name of the TPE material. Define the hardness you want in Shore A, the highest temperature the part will see, any oils or chemicals, and the substrate it must bond to. Those four answers point to the right family, and the family points to a short list of grades. Then ask for compliance documents if the part touches food or skin.

If you are designing a soft-touch or sealed part, our engineers can recommend a TPE family, plan the overmolding tool and quote the parts. See our service de moulage par injection de plastique, insert molding, and our guide to overmolding process and materials. When you are ready, upload your design for a quote ou rendez-vous sur Précision Tuowei.

Sources et lectures complémentaires
– International Organization for Standardization, ISO 18064 Thermoplastic elastomers: Nomenclature and abbreviated terms: iso.org
– ASTM International, ASTM D2240 Standard Test Method for Rubber Property: Durometer Hardness: astm.org

Properties, hardness comparisons and bonding behavior are typical guidance. Always confirm against the material supplier’s datasheet and run adhesion tests on your actual substrate.

Portrait d'un membre de l'équipe de Tuowei Precision, vêtu d'un polo bleu, devant des machines CNC floues dans l'usine
À propos de l'auteur
Andy

Ingénieur de production chez tuoweiprecision

Rédigé par Andy, ingénieur de production chez TUOWEI Precision. Andy est spécialisé dans l'usinage CNC, la fabrication de précision et l'ingénierie de production. Il possède une expérience pratique dans l'accompagnement de projets, du prototypage rapide à la production à grande échelle. Il travaille en étroite collaboration avec les équipes d'ingénierie et de fabrication pour évaluer les matériaux, les tolérances, les procédés d'usinage et la fabricabilité des conceptions. Ses articles offrent des conseils pratiques et techniquement fondés pour aider les ingénieurs et les acheteurs à prendre de meilleures décisions en matière de fabrication, à optimiser l’efficacité de la production et à garantir une qualité constante des pièces. Découvrez les solutions d’usinage CNC et de fabrication sur mesure de TUOWEI Precision pour votre prochain projet.

Construisons ensemble l'avenir

Collaborez avec Tuowei Precision pour donner vie à votre vision

Du prototypage rapide à la production à grande échelle, Tuowei Precision propose des services d'usinage CNC fiables, alliant précision et régularité à chaque étape. Lancez votre projet dès aujourd'hui.

Prenez contact avec nous !
Réponse rapide garantie dans les 24 heures
🔐 Tous les téléchargements sont sécurisés et confidentiels

Explorer les idées et l'innovation

Consultez nos derniers guides sur l'usinage CNC, les matériaux, les finitions et les tendances du secteur pour prendre de meilleures décisions en matière de production.

Prenez contact avec nous !
Réponse rapide garantie dans les 24 heures
🔐 Tous les téléchargements sont sécurisés et confidentiels