首页 » 博客 » 博客 » Face Milling vs Peripheral Milling: Differences, Tools & When to Use Each

Face Milling vs Peripheral Milling: Differences, Tools & When to Use Each

目录

拓维精密

需要专业的机械加工解决方案吗?拓维模型的团队随时准备为您提供全方位的制造支持。立即联系我们,获取您正在进行或即将开展的项目的报价!

Face milling vs peripheral milling

Face milling and peripheral milling are the two basic ways a milling cutter can remove material from a workpiece. The difference comes down to which part of the cutter does the work. In face milling, the cutter axis is perpendicular to the surface being machined and the cutting happens at the end face of the tool. In peripheral milling, the cutter axis is parallel to the machined surface and the teeth on the outside diameter (the periphery) do the cutting.

That single difference in orientation changes the cutting forces, the surface finish, the tools you use and the features you can make. This peripheral milling guide explains both methods in plain terms, corrects a few common myths, and gives you the numbers machinists actually use: stepover, lead angle, chip thinning and a worked feeds and speeds example.

Face milling vs peripheral milling: cutter axis perpendicular vs parallel to the surface
Face milling cuts with the cutter axis perpendicular to the surface; peripheral milling cuts with the axis parallel to it.

Face Milling vs Peripheral Milling at a Glance

系数 端面铣削 Peripheral milling
Cutter axis vs machined surface Perpendicular Parallel
Teeth doing the cutting End face (with corner edges) Outside diameter (flutes)
Typical surface produced Large flat faces, top surfaces Walls, shoulders, slots, profiles, contours
Main force direction Axial, into the spindle Radial, pushing the tool sideways
Typical tools Face mills, shell mills, fly cutters, high feed mills End mills, slab mills, side and face cutters, slitting saws
Typical width of cut 60% to 80% of cutter diameter 5% to 100% of tool diameter
Typical depth of cut Shallow axial depth, often 0.5 to 5 mm Deep axial depth possible, often 1 to 3 times diameter on walls
Main risk Poor flatness on thin plates, step lines between passes Tool deflection, wall taper, chatter on long tools
Best finish on Flat faces (Ra 0.4 to 1.6 µm with wiper inserts) Side walls (Ra 0.8 to 3.2 µm in a finish pass)
机器 Vertical machining center (most common) Vertical or horizontal machine

In short, the difference between face milling and peripheral milling depends on which teeth on the cutter do the work. Face milling produces flat faces with the cutter face, while peripheral milling and face milling together cover almost every prismatic part. Common peripheral milling applications are walls, slots, pockets and profiles, so peripheral milling is preferred wherever the workpiece needs a side feature. In a real CNC milling process, milling often combines both: peripheral milling is one of the two basic milling applications, and the right milling strategy depends on part geometry, tool engagement and material, from aluminum to stainless steel. Choosing milling tools is part of that strategy, because every milling cutter to remove material is built for one of these two cutting directions.

What Is Face Milling?

Face milling is a machining process in which the milling cutter is positioned perpendicular to the workpiece, so the cutter face and the bottom face of the tool remove material to produce a flat surface. A face mill is usually a large diameter body (50 to 160 mm is common on CNC machining centers) with several indexable carbide inserts around its rim. Most of the metal is cut by the insert corners and the short edge near the bottom of the tool, while the flat bottom edge (or a wiper flat on the insert) smooths the surface.

Shops use face milling to:

  • Square up raw stock and bring it to thickness
  • Clean up saw cut or cast surfaces
  • Create datum faces for later operations
  • Machine large flat sealing or mounting surfaces where flatness matters

Face mill types and lead angle

The lead angle (also called entering angle) is the angle between the cutting edge and the surface. It controls chip thickness, force direction and what shapes the cutter can make:

  • 90° (square shoulder) cutters can face and cut a true 90° shoulder in one tool. Forces are mostly radial, so they suit lighter machines and thin walls.
  • 45° face mills are the general purpose choice. They spread the cut over a longer edge, push force axially into the spindle, reduce exit burrs and allow higher feed. They cannot cut a square shoulder.
  • High feed cutters (10° to 15°) take very shallow depths at very high feed per tooth. They are excellent for roughing big flat areas and for long reach work because most force goes up into the spindle.
  • Fly cutters use one cutting point. They give a good finish on soft metals and plastics but remove metal slowly.
  • Round insert cutters are strong and forgiving in hard or interrupted cuts.

What Is Peripheral Milling?

Peripheral milling (also called plain milling) is a machining process that removes material from the workpiece with the teeth on the circumference of the cutter, while the cutter axis stays parallel to the machined surface. On a modern vertical machining center, this is what an end mill does when it cuts the side wall of a pocket or the outside profile of a part. On a horizontal mill, an arbor mounted slab mill does the same thing to a wide flat surface.

As a machining operation, peripheral milling is used for anything that is not a top face: walls, shoulders, slots, keyways, outside profiles and 3D contours. Because the flute length can be long, it can cut deep features in one pass that a face mill cannot reach.

How the peripheral milling process works

A typical peripheral milling operation on a CNC machining center runs in five steps:

  1. Fix the workpiece in a vise or fixture so the wall being cut is fully supported.
  2. Choose the cutting tool: diameter, flute count, flute length and coating to suit the material and wall depth.
  3. Set the engagement: axial depth (ap) along the flutes and radial width (ae) into the wall.
  4. Cut in climb milling with a rough pass that leaves 0.2 to 0.5 mm of stock on the wall.
  5. Finish with a light radial pass at full depth so the wall comes out straight and to size.

Peripheral milling cutters and machines

Peripheral milling tools on vertical machining centers include solid carbide end mills (2 to 6 flutes), indexable shoulder mills 和 chamfer mills. Peripheral end milling is the most common form today. On horizontal mills, slab mills, side and face cutters, slitting saws and form cutters are mounted on an arbor. Long walls and deep slots favor short, large diameter tools, because rigidity sets the limit before spindle power does.

Advantages and limitations of peripheral milling

优势 限制
Cuts deep walls, slots and profiles that a face mill cannot reach Side load bends the tool, so walls can taper
One end mill can rough and finish many features in one setup Long tools chatter, which limits depth and finish
Light stepover toolpaths give high feed and long tool life Scallop lines on floors if used for flat areas
Good wall finish and position accuracy with a spring pass Internal corners always keep the tool radius

Types of peripheral milling

操作 它能做什么 Typical tool
Slab (plain) milling Wide flat surface parallel to the cutter axis Helical slab mill on a horizontal arbor
Side milling Vertical face on one side of the part Side and face cutter, end mill
Straddle milling Two parallel faces at once, for example the width of a lug Two side cutters on one arbor
Gang milling Several surfaces in one pass in production Multiple cutters on one arbor
Slot milling Slots and keyways, often full width cut End mill, slot drill, slitting saw
Profile milling Outside and inside 2D contours End mill
Shoulder milling Floor plus wall at 90° (combined face and peripheral) Square shoulder mill, end mill
Form milling Special profiles such as radii or gear teeth Form cutter

The 6 Real Differences That Matter on the Shop Floor

1. Cutting direction and forces

In face milling the force runs mostly along the spindle axis, so the machine’s stiffest direction takes the load. In peripheral milling the force pushes the tool sideways. That sideways force bends the tool, which is why peripheral milling is far more sensitive to tool stickout and diameter. A useful rule: tool deflection rises with the cube of stickout, so doubling stickout gives about eight times the bend.

2. Engagement: face milling is not “full width”

Several popular guides say face milling uses the full width of the cutter. In practice, running a face mill dead center on a surface the same width as the cutter is one of the worst setups: chips are thinnest at entry, edges rub, and vibration rises. The standard practice is to choose a cutter about 20% to 50% wider than the cut and offset it so the width of cut is about 60% to 80% of the cutter diameter. For faces wider than the cutter, plan overlapping passes with about 10% to 20% overlap.

Peripheral milling uses a much wider range of radial engagement, from a 5% finishing pass to a 100% slot.

3. Chip thinning (the part most guides skip)

The actual chip thickness is not the same as the programmed feed per tooth (fz). Two things thin the chip:

Lead angles 90°, 45° and 15° and how chip thickness changes in face milling
A smaller lead angle spreads the cut over a longer edge, so the chip gets thinner. A 15° high-feed cutter thins the chip to about 26% of the feed per tooth.

Lead angle (face milling): h_ex = fz × sin(κr). A 45° face mill at 0.20 mm/tooth makes a chip only about 0.14 mm thick. To get the chip load the insert is designed for, you raise the feed by about 1.4×. A 15° high feed cutter thins the chip to about 26% of fz, which is why those tools run at 1 to 2 mm/tooth.

Radial engagement (peripheral milling): when width of cut (ae) is under half the tool diameter (D), h_ex = fz × 2√((ae/D) × (1 − ae/D)). At 10% radial engagement the chip is only 0.6 × fz. If you do not compensate, the tool rubs instead of cutting, heats up and wears fast. This is the reason modern high efficiency and trochoidal toolpaths use light stepovers with high feed rates.

4. Surface finish and texture

Face milling gives the best result on flat surfaces. A finishing pass with wiper inserts can reach Ra 0.4 to 0.8 µm on aluminum and Ra 0.8 to 1.6 µm on steel. The typical pattern is a crosshatch of arcs. If the spindle is not perfectly square to the table (tram), the trailing edge recuts the surface and leaves a crosshatch. A slight tilt so that only the leading edge cuts gives a cleaner one direction pattern.

Peripheral milling gives the best result on walls. A light finish pass (about 0.1 to 0.5 mm radial) with a sharp end mill in climb milling typically gives Ra 0.8 to 3.2 µm. Where peripheral milling is used on a floor (for example, a slab mill or a stepover pattern with an end mill), it leaves scallop lines that are harder to remove than face milling marks.

5. Depth of cut and material removal

It is a myth that face milling always removes metal faster. A large face mill with many inserts removes a lot of material per minute on open flat areas, but an end mill using its full flute length on a wall with a light stepover can match or beat it, especially on modern high speed machines. The worked example below shows the actual numbers.

6. Accuracy you can expect

Face milling controls flatness 和 parallelism of a face. Peripheral milling controls wall position, perpendicularity and profile. On a well maintained machine, ±0.025 mm on wall position and 0.02 to 0.05 mm flatness over 100 mm are realistic. Tighter results need a finish pass, stable workholding and stress relieved stock. See our guide on realistic CNC machining tolerances for more detail.

Worked Example: Feeds, Speeds and Removal Rate for Each Method

The key peripheral milling parameters and face milling parameters use the same formulas:

  • Spindle speed: n (rpm) = (Vc × 1000) ÷ (π × D)
  • Table feed: vf (mm/min) = fz × z × n
  • Material removal rate: Q (cm³/min) = ap × ae × vf ÷ 1000

Where Vc is cutting speed (m/min), D is tool diameter (mm), z is the number of teeth, ap is axial depth and ae is radial width of cut.

Face milling 6061 aluminum, 63 mm face mill, 5 inserts, 90° lead

  • Vc 600 m/min gives n = 600,000 ÷ (π × 63) ≈ 3,030 rpm
  • fz 0.15 mm gives vf = 0.15 × 5 × 3,030 ≈ 2,270 mm/min
  • ap 2 mm, ae 45 mm (about 70% of diameter)
  • Q = 2 × 45 × 2,270 ÷ 1000 ≈ 204 cm³/min

Peripheral milling a wall in 6061, 12 mm 3 flute carbide end mill

  • Vc 300 m/min gives n = 300,000 ÷ (π × 12) ≈ 7,960 rpm
  • ae 1.2 mm (10% of diameter), so the chip thinning factor is 0.6. To hold a 0.06 mm real chip, fz = 0.06 ÷ 0.6 = 0.10 mm
  • vf = 0.10 × 3 × 7,960 ≈ 2,390 mm/min
  • ap 24 mm (2 × D, full flute wall)
  • Q = 24 × 1.2 × 2,390 ÷ 1000 ≈ 69 cm³/min

The face mill wins on an open flat area, but the end mill does work the face mill cannot do at all: a 24 mm deep wall in one pass. Values like these are starting points. Always check the tool maker’s data for your exact grade, coating and machine.

Peripheral milling starting speeds by material

Typical starting values for a 10 to 12 mm carbide end mill in a side milling cut. Check your tool maker’s data before running.

材料 Cutting speed Vc (m/min) Feed per tooth fz (mm) 说明
Aluminum 6061 / 7075 300 to 600 0.05 to 0.15 Polished 2 or 3 flute, air or mist to clear chips
Mild steel 1018 / 1045 120 to 200 0.04 to 0.10 AlTiN coated 4 flute, flood coolant
Stainless 304 / 316 70 to 120 0.03 to 0.08 Never let the tool rub, it work hardens the wall
灰口铸铁 100 to 180 0.05 to 0.12 Often cut dry with air, watch for edge chipping at exit
钛 Ti-6Al-4V 40 to 70 0.03 to 0.07 Low radial engagement, high pressure coolant
Nickel alloys (Inconel 718) 20 to 40 0.02 to 0.06 Very low radial engagement, sharp coated tool, rigid setup
黄铜 C360 150 to 300 0.05 to 0.15 Uncoated or DLC, can run dry
Acetal (POM) and other plastics 150 to 300 0.08 to 0.20 Sharp 1 or 2 flute, air blast to stop melting

Climb vs Conventional Milling in Peripheral Cuts

Peripheral milling has one extra choice that face milling mostly avoids: the direction the cutter rotates relative to the feed.

Climb milling vs conventional milling in peripheral milling cuts
In climb milling the chip runs thick to thin; in conventional milling it runs thin to thick.
Climb milling (down milling) Conventional milling (up milling)
Chip shape Thick to thin Thin to thick
Tool life Longer, less rubbing Shorter, edge rubs at entry
表面处理 更好 Worse, more work hardening
最适合 CNC machines with ballscrews, finishing, stainless and titanium Old manual machines with backlash, hard scale or cast skin

On CNC machining centers, climb milling is the default for almost all peripheral cuts. In face milling, both happen at once across the cutter, which is another reason to offset the face mill so more of the cut is in the climb direction.

Which Method Makes Which Feature on Your Drawing?

This is the question buyers and designers really ask. Use this map when you review a part:

Machined part showing top face, walls, pocket and slot made by peripheral milling
Top faces are face milled; walls, pockets and slots are cut by peripheral milling.
Feature on the drawing Usual operation 为什么
Top face, datum face, sealing face 端面铣削 Best flatness and finish on large flats
Outside profile, side walls Peripheral milling (end mill) Cutter axis parallel to the wall
Pocket walls Peripheral milling Same as above, finished with a light radial pass
Pocket floor End mill bottom (a small face milling action) Face mill cannot fit inside the pocket
Step or shoulder at 90° Shoulder milling (both at once) Square shoulder cutter or end mill cuts floor and wall together
Slots and keyways Peripheral slot milling Full width cut, watch chip evacuation
45° chamfer on edges Chamfer mill (peripheral) Edge of the tool forms the angle
Large wide flat on a long part Face milling, or slab milling on a horizontal machine High removal rate
3D surface, mold cavity Ball end mill contouring Peripheral and tip cutting combined

Common Problems and How to Fix Them

问题 Usually in 可能原因 修复
Wall taper (wider at bottom) Peripheral Tool deflection from long stickout or heavy radial cut Shorter tool, larger diameter, light spring pass, variable helix end mill
锉痕 两者 Low rigidity, wrong engagement, long overhang Change rpm by 10% to 15%, reduce stickout, use variable pitch tool
Step lines between passes Face Spindle tram out, insert height runout Tram the head, use wiper inserts, overlap passes 10% to 20%
Plate warps after unclamping Face 坯料中的残余应力 Machine both sides alternately, rough, release clamps, then finish
Burrs on exit edge 两者 Feed direction off the edge, sharp lead angle Use 45° cutter, chamfer pass, plan exit into material
Fast edge wear in stainless Peripheral Rubbing from radial chip thinning Increase fz to compensate, climb mill, coolant through tool

Design Tips to Cut Machining Cost

Knowing which operation makes each feature helps you design cheaper parts:

  • Keep pocket depth under 4 × the corner tool diameter. Deeper walls need long tools, slow feeds and extra finish passes.
  • Add internal corner radii slightly larger than the tool radius (for example R3.2 instead of R3 for a 6 mm tool) so the end mill can keep moving instead of stopping in the corner.
  • Avoid thin tall walls. Keep metal walls above about 0.8 mm and wall height under about 10 × thickness to limit deflection and chatter.
  • Only call out tight flatness where it is needed. A sealing face needs a dedicated face milling finish pass. A cosmetic face does not.
  • Put datum faces on accessible top surfaces so they can be face milled in the same setup as the walls.

If your part needs both tight flatness and deep pockets, 5-axis milling can reduce setups. Read when 5 axis machining is worth the cost.

How Tuowei Precision Chooses Between Face and Peripheral Milling

At Tuowei Precision, parts are process planned before cutting starts. Large datum and sealing faces are face milled first with indexable cutters to create a stable reference. Walls, pockets, profiles and slots are then rough machined with high-efficiency milling toolpaths and finished with a separate light radial pass to hold position and finish. Aluminum, steel, stainless and titanium each get their own cutting data and tool coatings.

Need parts that combine flat datum faces, deep pockets and tight wall tolerances? Explore our 数控铣削服务 or upload your drawing for an 即时报价.

常见问题

Is end milling the same as peripheral milling?

Not exactly. End milling is a tool category, not a cutting direction. An end mill does peripheral milling when its side flutes cut a wall, and it does a small amount of face milling when its bottom edges cut a floor. Most CNC end mill work is a mix of both.

Which gives a better surface finish, face milling or peripheral milling?

Face milling gives the better finish on flat faces, especially with wiper inserts. Peripheral milling gives the better finish on side walls. Each method is best on the surface it is designed to cut.

Can a face mill cut a 90° shoulder?

Only a 90° (square shoulder) face mill can. A 45° or high feed face mill leaves an angled or radiused step because of its lead angle.

Is slot milling a type of peripheral milling?

Yes. In slot milling the tool cuts with its full diameter in the side flutes. It is one of the hardest peripheral cuts because chips have nowhere to escape, so feeds are lower than in side milling.

What stepover should I use for face milling?

Use about 60% to 80% of the cutter diameter as the width of cut, with the cutter offset from the center line. For surfaces wider than the cutter, overlap passes by about 10% to 20%.

What is the difference between slab milling and face milling?

Slab milling is peripheral milling with a wide cylindrical cutter on a horizontal arbor. It cuts a flat surface with the teeth on its outside. Face milling cuts the same kind of flat surface with the end of a cutter held perpendicular to it. Face milling is far more common on CNC machining centers today.

Why does peripheral milling cause tapered walls?

The side load bends the tool away from the wall, more at the tip than at the shank. The result is a wall that is thicker at the bottom. Shorter tools, lighter finish passes and a spring pass fix it.

What machine is used for peripheral milling?

Most peripheral milling today is done on CNC vertical machining centers with end mills. Horizontal milling machines with arbor mounted slab, side and straddle cutters are still used for wide surfaces and high volume production.

What is the difference between side milling and end milling?

Side milling is a type of peripheral milling that cuts a vertical face with the teeth on the side of the cutter. End milling is a broader term for any cut made with an end mill, which can use its side teeth, its end teeth or both at once.

Is milling harder than turning on a lathe?

Milling is usually more complex to program and set up, because the tool moves in several axes around a fixed part. Turning is simpler for round parts, since the part spins and a single point tool shapes it. See our guide to lathe cutting tools for the turning side.

图为拓维模型的一名员工身穿蓝色Polo衫,站在工厂内背景模糊的数控机床前
关于作者
安迪

tuoweiprecision 制造工程师

作者:安迪,拓维模型制造工程师。. 安迪专攻数控加工、精密制造和生产工程领域,在从快速原型制作到大规模量产的整个项目过程中拥有丰富的实践经验。他与工程和制造团队紧密合作,共同评估材料、公差、加工工艺以及设计可制造性。 他的文章提供了实用且具有技术深度的见解,旨在帮助工程师和采购人员做出更明智的制造决策、优化生产效率,并确保零件质量的一致性。欢迎了解拓维模型的数控加工和定制制造解决方案,为您的下一个项目提供支持。.

让我们携手共创未来

与拓维模型携手,共同实现您的愿景

从快速原型制作到可扩展的生产,Tuowei Precision 提供可靠的数控加工服务,在每个环节都确保精度与一致性。立即启动您的项目。.

与我们联系!
保证在24小时内及时回复
🔐 所有上传内容均安全保密

探索洞察与创新

阅读我们关于数控加工、材料、表面处理及行业趋势的最新指南,以做出更明智的生产决策。

与我们联系!
保证在24小时内及时回复
🔐 所有上传内容均安全保密